manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 146

3  Tests and Diagnostics 

 3.9 Display Test 

  

Subtest 04 

Gradation & Mode test for VGA  

This subtest displays gradations for following modes. To change the mode, 
press 

Enter

.  

 [Mode 

12] 

 [Mode 

13] 

 [Mode 

3] 

  [Mode 111   640*480  64K] 

  [Mode 112   640*480  16M] 

  [Mode 114   800*600  64K] 

  [Mode 115   800*600  16M] 

 [Mode 

117 1024*768 

 64K] 

 [Mode 

118 1024*768 

 16M] 

 

The display below appears on the screen when this subtest is executed. 

 

 

(Display example: Mode 12) 

To exit this subtest and return to the DISPLAY TEST menu, press 

Enter

 

after 

displaying the Mode 118

.

 

Subtest 05 

All dot on/off for LCD 

This subtest displays an all-white screen then an all-black screen. The display 
changes automatically every three seconds and the screen returns to the 
DISPLAY TEST menu. 

3-20 

[CONFIDENTIAL] 

TECRA M9 Maintenance Manual (960-631)) 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды