manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 153

3.13 Hard Disk Test 

3  Tests and Diagnostics 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

3-27 

3.13  Hard Disk Test 

To execute the Hard Disk Test, select 

8

 from the DIAGNOSTIC TEST MENU, press 

Enter

, 

and follow the directions on the screen. 

CAUTION

:  The contents of the hard disk will be erased when subtest 02, 03, 04, 06, 08 

or 09 is executed. Before running the test, the customer should transfer the 
contents of the hard disk to floppy disk or another hard disk. If the customer 
has not or can not perform the back-up, create back-up disks as described 
below. 

   

 

 

Check to see if the Microsoft Create System Disks Tools (MSCSD.EXE) still 

exists in the System Tools Folder. (This tool can be used only once.) If it 
exists, use it to back up the pre-installed software, then use the Backup 
utility in the System Tools folder to back up the entire disk, including the 
user’s files. 

   

 

 

Refer to the operating system instructions. 

1.

 

The following message appears for the error dump operation when a data compare 
error is detected. Select 

1

 or 

2

. 

Data compare error dump  (1:no, 2:yes) 

 

2.

 

The following message appears for whether or not the HDC status is displayed on the 
screen. The HDC status is described in section 3.19. Select 

1

 or 

2

. 

Detail status display   (1:no, 2:yes) 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды