Toshiba Tecra M9 Скачать руководство пользователя страница 269

Страница: 269 / 414

4.12 Wireless LAN card/3G card

4 Replacement Procedures

TECRA M9 Maintenance Manual (960-631)

[CONFIDENTIAL]

4-35

Installing the Wireless LAN card/3G card

The following describes the procedure for installing the wireless LAN card/3G card. (See
Figure 4-19 and 4-20.)

CAUTION:

Be sure to switch the computer off before installing the wireless LAN card.

Otherwise, the computer or the wireless LAN card may be damaged.

Arrange the

wireless LAN antenna cables

(black, white and gray) and

3G antenna

cables

(red and blue) through the hole of the cover assembly.

Insert the

wireless LAN card

to the connector on the system board slantwise and

press it to connect firmly.

Connect the

wireless LAN antenna cables

(white: 1, black: 2, gray: 3) to the

connectors on the wireless LAN card.

Insert the

3G card

to the connector on the system board slantwise and press it to

connect firmly.

Connect the

3G antenna cables

(red and blue) to the connectors on the 3G card.

Содержание Tecra M9































































































































































































































































































































































































































Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra M9, Руководство по обслуживанию

Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды