manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 265

4.12 Wireless LAN card/3G card 

4  Replacement Procedures 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

4-31

 

4.12  Wireless LAN card/3G card 

4.12.1 Removing the Wireless LAN card/3G card  (Not Smart card Model) 

The following describes the procedure for removing the wireless LAN card/3G card. (See 
Figure 4-19 and 4-20.) 

CAUTION:  

Do not try to remove the wireless LAN card/3G card with the computer 

turned on. It may cause damages to the computer or the wireless LAN 
card/3G card. Do not touch the connectors on the wireless LAN card on the 
computer. Debris on the connectors may cause the wireless LAN card access 
problems. 

1.

 

Peel off the 

insulator

 that prevents a waterdrop from entering the computer. 

2.

 

Remove the following 

screws

. 

•

 

M2

×

4B    

BIND screw   

 

×

2 

3.

 

Disconnect the 

3G antenna cables

 (red and blue) from the 3G card using an antenna 

coaxial cable disconnector. 

4.

 

Disconnect the 

3G card

 from the connector on the system board. 

5.

 

Remove the following 

screws

. 

•

 

M2

×

4B    

BIND screw   

 

×

2 

6.

 

Disconnect the 

wireless LAN antenna cables

 (black, white and (gray)) from the 

wireless LAN card using an antenna coaxial cable disconnector. 

7.

 

Disconnect the 

wireless LAN card

 from the connector on the system board.  

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды