Toshiba Tecra M9 Скачать руководство пользователя страница 212

Страница: 212 / 414

3 Tests and Diagnostics

3.31 SETUP

Moving Within the SETUP Menu and Changing Values

Press

and

to move between the two columns. Press

↑

and

↓

to move between

items in a column. Press

↑ (

PgUp)

and

↓ (

PgDn)

to move between the

two pages.

Press either the

Space bar

Back Space

to change the value.

Accepting Changes and Exiting the SETUP Window

Press

End

to accept the changes you made.

If the changed item does not require the system to reboot, the following message is
displayed:

Are you sure? (Y/N)

If the changed item requires the system to reboot, the following message is displayed:

Are you sure? (Y/N)

The changes you made will cause the system to reboot.

To make other changes, press

. Repeat the steps above.

To accept the changes, press

3-86

[CONFIDENTIAL]

TECRA M9 Maintenance Manual (960-631)

Содержание Tecra M9































































































































































































































































































































































































































Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra M9, Руководство по обслуживанию

Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды