manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 149

3.10 Floppy Disk Test 

3  Tests and Diagnostics 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

3-23 

Select the number of the subtest you want to execute and press 

Enter

. The following 

message will appear during the floppy disk test. 

FLOPPY DISK  IN PROGRESS  XXXXXXX

xxx DIAGNOSTIC TEST VX.XX 

 [Ctrl]+[Break] :  test end 

 [Ctrl]+[C] 

:  key stop 

SUB-TEST   : 

XX 

PASS COUNT   : XXXXX   ERROR COUNT  : XXXXX 

WRITE DATA   : XX      READ DATA    : XX 

ADDRESS      : XXXXXX STATUS    : 

XXX 

 

When the subtest 04 or 05 is selected, the following messages will appear on the screen. 
Select the test data

 

(

subtest 04 only), track number and head number you want to test. 

Test data  ?? (subtest 04 only) 

Track No.  ?? 

Head No.  ? 

Subtest 01 

Sequential read 

This subtest performs a Cyclic Redundancy Check (CRC) that continuously 
reads all the tracks (track: 0 to 39/0 to 79) on a floppy disk.  

Subtest 02 

Sequential read/write 

This subtest continuously writes data pattern B5ADADh to all the tracks 
(track: 0 to 39/0 to 79) on a floppy disk. The data is then read and compared 
to the original data.  

Subtest 03 

Random address/data 

This subtest writes random data to random addresses on all tracks (track: 0 to 
39/0 to 79) on a floppy disk. The data is then read and compared to the 
original data. 

Subtest 04 

Write specified address 

This subtest writes the data specified by an operator to a specified track, head 
and address. 

Subtest 05 

Read specified address 

This subtest reads data from a track, head and address specified by an 
operator.  

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды