manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 107

2.15 Sound Troubleshooting 

2  Troubleshooting Procedures

 

Procedure 2 

Connector Check 

The sound function-wiring diagram is shown below: 

 

Any of the connections may be disconnected. Disassemble the computer following the steps 
described in Chapter 4, 

Replacement Procedures

 and perform the following checks: 

1.

 

If the speakers do not work correctly, perform Check 1. 

2.

 

If the headphone does not work correctly, perform Check 2. 

3.

 

If the external microphones do not work correctly, perform Check 3. 

4.

 

If the Built in microphones do not work correctly, perform Check 4. 

Check 1  If the speakers do not work properly, the speaker cable may be disconnected. 

Make sure the speaker cable is firmly connected to CN6170 on the system board. 
If the stereo speakers are still not functioning properly, go to Procedure 3. 

Check 2  If the headphone does not work properly, the headphone cable may be 

disconnected. Make sure the headphone cable is firmly connected to J6310 on the 
system board. If the sound function still does not work properly, Procedure 3. 

Check 3  If the external microphones do not work properly, external microphone cable may 

be disconnected. Make sure the external microphone cable is firmly connected to 
J6051 on the system board.  

 

If the external microphones are still not functioning properly, go to Procedure 3. 

Check 4  If the Built in microphone do not work properly, the Built in microphone cable 

may be disconnected. Make sure the Built in microphone cable is firmly 
connected to CN6050 on the system board. If the Built in microphone are still not 
functioning properly, go to Procedure 3. 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL]

 

2-57 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды