Toshiba Tecra M9 Скачать руководство пользователя страница 181

Страница: 181 / 414

3.24 Floppy Disk Drive Utilities

3 Tests and Diagnostics

TECRA M9 Maintenance Manual (960-631)

[CONFIDENTIAL]

3-55

3.24.2 Operations

Selecting

from the DIAGNOSTIC MENU and pressing

Enter

displays the

following message.

[ FDD UTILITIES ]

1 - FORMAT

2 - COPY

3 - DUMP

4 – HDD-ID READ

9 - EXIT TO DIAGNOSTICS MENU

FORMAT program

(a)

Selecting FORMAT displays the following message.

DIAGNOSTICS - FLOPPY DISK FORMAT : VX.XX

Drive number select (1:A, 2:B) ?

(b)

Select a drive number to display the following message.

Type select (0:2DD, 3:2HD) ?

(c)

Select a media/drive type number and press

Enter

. A message similar to the

one below will be displayed.

Warning : Disk data will be destroyed.

Insert work disk into drive A:

Press any key when ready.

(d)

Remove the Diagnostics Disk from the FDD, insert the work disk and press
any key.

The following message will be displayed when the FDD format is executed.

[ FDD TYPE ] : TRACK = XXX

[ FDD TYPE ] : HEAD = X

[ FDD TYPE ] : SECTOR = XX

Format start

[[track, head = XXX X]]

After the floppy disk is formatted, the following message will appear.

Format complete

Another format (1:Yes/2:No) ?

(e)

Typing

displays the message from step (c) above. Typing

returns the test

to the DIAGNOSTIC MENU.

Содержание Tecra M9































































































































































































































































































































































































































Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra M9, Руководство по обслуживанию

Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды