manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 80

2  Troubleshooting Procedures 

2.4 System Board Troubleshooting

 

2-30 [CONFIDENTIAL]

 

TECRA M9 Maintenance Manual (960-631) 

Procedure 3 

Diagnostic Test Program Execution Check 

Execute the following tests from the Diagnostic Test Menu. Refer to Chapter 3, 

Tests and 

Diagnostics,

 for more information on how to perform these tests. 

1.

 

System test 

2.

 

Memory test 

3.

 

Keyboard test 

4.

 

Display test 

5.

 

Floppy Disk test 

6.

 

Async test 

7.

 

Hard Disk test 

8.

 

Real Timer test 

9.

 

NDP test 

10.

 

Expansion test 

11.

 

CD-ROM/DVD-ROM test 

12.

 

Wireless LAN test 

13.

 

Sound test 

14.

 

LAN/Modem/Bluetooth/IEEE1394 test 

If an error is detected during these tests, go to Procedure 4. 

Procedure 4 

Replacement Check 

The system board connectors may be disconnected. Disassemble the computer following the 
steps described in Chapter 4, 

Replacement Procedures

 and perform Check 1. 

Check 1  Visually check for the following: 

a)

 

Cracked or broken connector housing 

b)

 

Damaged connector pins 

If their connectors are in good condition, but there is still a problem, go to Check 
2. 

Check 2  The system board may be damaged. Replace the system board with a new one 

following the steps described in Chapter 4, 

Replacement Procedures

.  

 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды