Toshiba Tecra M9 Скачать руководство пользователя страница 292

Страница: 292 / 414

4 Replacement Procedures

4.19 System board

Installing the system board

The following describes the procedure for installing the system board and LCD cover
assembly. (See Figure 4-30.)

Install the

system board

on the base assembly.

Install the

modem cable holder

to the slot.

NOTE:

When installing a new modem cable holder, reuse the

double-sided tape

and stick

it in place. If the adhesive strength of the double-sided tape on the modem cable
holder is weak, replace it with a new one.

Install the

modem jack, DC-IN jack

and

HDD cable

to the slot.

NOTE:

Arrange the modem cable on the modem cable holder as shown in the figure

below.

Modem cable

Stick the

insulator

in place.

Connect the Bluetooth cable to the connector

CN4400

on the system board.

4-58

[CONFIDENTIAL]

TECRA M9 Maintenance Manual (960-631)

Содержание Tecra M9































































































































































































































































































































































































































Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra M9, Руководство по обслуживанию

Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды