manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 85

2.6 HDD Troubleshooting 

2  Troubleshooting Procedures

 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL]

 

2-35 

Procedure 2 

Partition Check 

Insert the Toshiba MS-DOS system disk and restart the computer with U key holding down. 
Perform the following checks:  

Check 1  Type 

C:

 and press 

Enter

. If you cannot change to drive C, go to Check 2. If you 

can change to drive C, go to Check 3. 

Check 2  Type 

FDISK

 and press 

Enter

. Choose Display Partition Information from the 

FDISK menu. If drive C is listed, go to Check 3. If drive C is not listed, return to 
the FDISK menu and choose the option to create a DOS partition on drive C. 
Restart the computer from the Toshiba MS-DOS system disk. If the problem still 
exists, go to Procedure 3. 

Check 3  If drive C is listed as active in the FDISK menu, go to Check 4. If drive C is not 

listed as active, return to the FDISK menu and choose the option to set the active 
partition for drive C. Restart the computer and then go to Procedure 3.

 

Check 4  Remove the FD and restart the computer. If the problem still exists, go to 

Procedure 3. 

Check 5  Using the 

SYS 

command on the Toshiba MS-DOS system disk, install system 

files on the HDD. 

If the following message appears on the display, the system files have been 
transferred to the HDD. Restart the computer. If the problem still exists, go to 
Procedure 3. 

System transferred 

NOTE

:  If the computer is running Windows 2000, OSR2 or higher and the hard disk has 

more than 512 MB capacity, the FDISK program will ask if you need support for 
a partition larger than 2GB. Select Y for large partition support; however, be 
sure to read the precaution regarding access by other operating systems.

 

 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды