manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 304

4  Replacement Procedures 

4.23 North bridge heat sink/CPU heat sink/Fan/CPU 

 

Rev D 

4.

 

Apply new 

grease

(DENKA GFC-F1)  on the CPU and North bridge using a special 

syringe as shown in the following figure. Apply quarter of scale (0.25ml) of grease 
evenly on the CPU chip and North bridge chip. When silicon grease is already 
applied to the CPU and North bridge, wipe them off with a cloth in advance. (In the 
case of the Built-in GPU model.)  

5.

 

Apply new 

grease

(DENKA GFC-F1)  on the CPU and GPU using a special syringe 

as shown in the following figure and stick the new cool sheet on the North bridge . 
Apply quarter of scale (0.25ml) of grease evenly on the CPU and GPU chip. When 
silicon grease is already applied to the CPU and GPU, wipe them off with a cloth in 
advance. (In the case of the GPU model.) 

CAUTION: Do not apply silicon grease on the North bridge. (In the case of the GPU 
model.)

 

 

Figure 4-40  Applying new grease 

6.

 

Stick the 

insulator

 to the fan in place to secure the fan cable to the fan. 

7.

 

Install the 

fan 

to the 

CPU heat sink 

and secure them with the following 

screws

. 

•

 

M2.5

×

3B   

FLAT HEAD screw   

 

×

2 

8.

 

Install the 

fan holder

 in place. 

9.

 

Install the 

CPU heat sink 

(with the fan) in place. 

4-70 

[CONFIDENTIAL] 

 

TECRA M9 Maintenance Manual (960-631) 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды