Toshiba Tecra M9 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 414

Toshiba Tecra M9 Скачать руководство пользователя страница 42

1 Hardware Overview

1.9 Batteries

28

[CONFIDENTIAL]

TECRA M9 Maintenance Manual (960-631)

1.9.2

Battery Charging Control

Battery charging is controlled by a power supply microprocessor. The microprocessor
controls whether the charge is on or off and detects a full charge when the AC adaptor and
battery are attached to the computer. The system charges the battery.

Battery Charge

When the AC adaptor is attached, there are two types of charge: When the system is powered
off and when the system is powered on. Table 1-8 lists the charging time required for charges.

Table 1-8 Time required for charges

Battery type

Power on

(hours)

Power

off

(hours)

Battery(4,000 mAh)

About 4.5 to 9.5

About 2.5

Battery(5,100 mAh)

About 5.5 to 12.0

About 3.0

Extended capacity

Battery(7,050 mAh)

About 8.0 to 19.5

About 3.5

High capacity battery(8,800 mAh)

About 9.0 to 21.0

About4.0

NOTE:

The time required when the system is powered on is affected by the amount of

power the system is consuming. Use of the fluorescent lamp and frequent disk
access diverts power and lengthens the charge time.

If any of the following occurs, the battery charge process stops.

1. The battery becomes fully charged.

2. The AC adaptor or battery is removed.

3. The battery or output voltage is abnormal.

Detection of full charge

A full charge is detected only when the battery is charging at charge. A full charge is
detected under any of the following conditions:

1. The current in the battery charging circuit drops under the predetermined limit.

2. The charging time exceeds the fixed limit.

«
...
40
41
42
43
44
...
»

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды