manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 84

2  Troubleshooting Procedures  

2.6 HDD Troubleshooting

 

2-34

 

[CONFIDENTIAL]

 

TECRA M9 Maintenance Manual (960-631) 

2  

2.6 HDD 

Troubleshooting 

This section describes how to determine if the HDD is functioning properly. Perform the 
steps below starting with Procedure 1 and continuing with the other procedures as required. 

Procedure 1:  Message Check 
Procedure 2:  Partition Check 
Procedure 3:  Format Check 
Procedure 4:  Diagnostic Test Program Execution Check 
Procedure 5:  Connector Check and Replacement Check 

CAUTION

:  The contents of the hard disk will be erased when you execute the HDD 

troubleshooting procedures. Transfer the contents of the hard disk to floppy 
disks or other storage media.  

Procedure 1 

Message Check 

When the computer’s HDD does not function properly, some of the following error messages 
may appear on the display. Start with Check 1 below and perform the other checks as 
instructed. 

Check 1  If any of the following messages appear, go to Procedure 5. If the following 

messages do not appear, perform Check 2. 

HDC ERROR (After 5 seconds this message will disappear.) 

or 

IDE #0 ERROR (After 5 seconds this message will disappear.)  

or 

IDE #1 ERROR (After 5 seconds this message will disappear.)  

Check 2  If either of the following messages appears, go to Procedure 2. If the following 

messages do not appear, perform Check 3. 

Insert system disk in drive 
Press any key when ready ..... 
     

or

 

Non-System disk or disk error 
Replace and press any key 

 

Check 3  Make sure the Hard Disk option is set to not used. If it is set to not used, choose 

another setting and restart the computer. If the problem still exists, go to 
Procedure 2. 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды