manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 272

4  Replacement Procedures 

4.12 Wireless LAN card/3G card 

4.12.2 Removing the Wireless LAN card  (Smart card Model only) 

The following describes the procedure for removing the wireless LAN card. (See Figure 4-
SC2 and 4-SC3.) 

CAUTION:  

Do not try to remove the wireless LAN card with the computer turned on. It 

may cause damages to the computer or the wireless LAN card. Do not touch 
the connectors on the wireless LAN card on the computer. Debris on the 
connectors may cause the wireless LAN card access problems. 

1.

 

Peel off the 

insulator

 that prevents a waterdrop from entering the computer. 

2.

 

Remove the following 

screws

. 

•

 

M2

×

4B    

BIND screw   

 

×

2 

3.

 

Disconnect the 

wireless LAN antenna cables

 (black, white and gray) from the 

wireless LAN card using an antenna coaxial cable disconnector. 

4.

 

Disconnect the 

wireless LAN card

 from the connector on the system board.  

 

 Wireless LAN antenna
  cable (gray) 

Wireless LAN antenna 

cable (white) 

 Wireless LAN card 

M2

×

4B BIND

Insulator 

 Wireless LAN antenna
  cable (black) 

Figure 4-SC2   Removing the wireless LAN card 

4-38 

[CONFIDENTIAL] 

TECRA M9 Maintenance Manual (960-631) 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды