manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 239

4.1 Overview 

4  Replacement Procedures 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

4-5

 

Assembly Procedure 

After the computer has been disassembled and the part that caused the fault has been repaired 
or replaced, the computer must be reassembled. 

Take note of the following general points when assembling the computer. 

•

 

Take your time and follow the instructions carefully. Hurrying the assembly work 

will only introduce new problems. 

•

 

Check that all cables and connectors are securely connected. 

•

 

Before fastening FRUs or other parts in place, ensure that no cables are caught on 

screws or the FRU. 

•

 

Check that all latches are securely closed. 

•

 

Ensure that you have installed all FRUs correctly and do not have any screws left 

over. Using an incorrect screw may damage the thread or screw head and result in the 
FRU not being securely fastened in place. 

After installing FRUs, check that the computer operates correctly. 

Tools and Equipment 

For your safety and the safety of the people around you, it is important that you use 
Electrostatic Discharge (ESD) equipment. Correctly utilizing of the equipment increases the 
percentage of successful repairs and saves on the cost of damaged or destroyed parts. The 
following equipment is required for disassembly and assembly. 

•

 

One Philips screwdriver with type 0 bit (for S-THIN HEAD screws) 

•

 

One Philips screwdriver with type 1 bit (for screws other than above) 

•

 

Tweezers (for lifting screws) 

•

 

ESD mats (lay on work table or floor) 

•

 

An ESD wrist strap and heel grounder 

•

 

Anti-static carpet or flooring 

•

 

A pair of needle-nose pliers 

•

 

Air-ionizers in highly static sensitive areas 

•

 

Antenna coaxial cable disconnector  

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды