Toshiba e-studio 2330C Скачать руководство пользователя страница 23

Страница: 23 / 262

e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C

1-14

(b) Enter the setting mode [08]. Change the value of the codes [5293] to [5296] to adjust fusing

temperature in the recycled paper mode. (In this step fusing temperature is adjusted to print the

high-density area of the image most clearly.)

Adjustment

Paper

type

[08]

code

Subco

Recomm

ended

value

Accept

able

value

range

Default

Normal temp /

Black

Normal temp /

Color

3 to 8

0 to 16

• e-STUDIO4520c

/4530c: 5

• Others: 4

Low temp /

Black

Center

heater

Low temp /

Color

Recycled

paper

08-5293

3 to 8

0 to 16

• e-STUDIO4520c

/4530c: 7

• Others: 6

Normal temp /

Black

Normal temp /

Color

3 to 8

0 to 16

• e-STUDIO4520c

/4530c: 5

• Others: 4

Low temp /

Black

Side

heater

Low temp /

Color

Recycled

paper

08-5294

3 to 8

0 to 16

• e-STUDIO4520c

/4530c: 7

• Others: 6

Normal temp /

Black

Normal temp /

Color

3 to 8

0 to 16

Low temp /

Black

Sub

heater

Low temp /

Color

Recycled

paper

08-5295

3 to 8

0 to 16

Normal temp /

Black

Normal temp /

Color

2 to 6

0 to 16

Low temp /

Black

Pressure

roller

Low temp /

Color

Recycled

paper

08-5296

2 to 6

0 to 16

• After adjusting the fusing temperature, perform automatic calibration.

* Refer to step (2) in “1.1 To Obtain a Darker Image”.

<Hint>

The smaller the setting value is, the lower the fusing temperature becomes. It is usually

recommended that the set value be decreased in order to suppress roughness on the high-density

area of the image. Adjust the value while checking the image carefully because if the value is

too small, insufficient fusing may occur.

Since temperatures on the long side of the paper cannot be kept in a proper balance, the same

value must be set for the [08] codes [5293] and [5294] unless otherwise required so.

After setting the value, print and check the image quality.

If further image quality adjustment is necessary, go to step (3).

1. General Adjustments – Copying, Printing and e-Filing (Output from Box)

Содержание e-studio 2330C

































































































































































































































































Результаты поиска

Содержание e-studio 2330C

Отзывы:

Похожие инструкции для e-studio 2330C

Бренды по названию

Популярные бренды

Toshiba e-studio 2330C, Руководство по визуализации

Результаты поиска

Содержание e-studio 2330C

Отзывы:

Похожие инструкции для e-studio 2330C

Бренды по названию

Популярные бренды