Toshiba e-studio 2330C Скачать руководство пользователя страница 19

Страница: 19 / 262

e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C

1-10

(b) Enter adjustment mode [05]. Select code [396]. Press the [START] button.

• Image quality control will be forcibly performed and the image density will be corrected.

<Note>

The above corrections will be effective immediately after the values for codes [08-2525

to 2527] are changed. After changing the values for codes [08-2525 to 2527], remember

to perform image quality control for code 05-396.

Repeatedly use steps (a) to (c) as necessary to select a proper value.

If further image quality adjustments are still necessary, use the next procedure.

(2) Check the life of the consumables (particularly the drum, developer material and transfer belt unit) and

replace them, if necessary.

• When replacing any consumable, use steps (a) to (b).

(a) Enter the PM support mode. Reset the counter corresponding to the replaced consumable to "0."

* For further information regarding the PM support mode, refer to the Service Handbook.

(b) Enter adjustment mode [05]. Select code [396]. Press the [START] button.

• Image quality control will be performed and the image quality control value will be initialized.

* After replacing any consumable, remember to reset the counter corresponding to it to "0." Otherwise, it

may cause a loss in MFP performance, including degradation in the image quality and a reduction in the

life of the consumables.

* While replacing any consumable, also check the slit glass in the laser optical unit, and thoroughly clean it,

if it is soiled.

Precautions after the completion of the adjustment

• The adjustment may possibly provide extremely dark images (decreased resolving power, inadequate

reproducibility of gradations), and extremely light images (blurred images, faint thin lines). Therefore,

carefully perform the adjustment, while checking the copy or print image.

• No effect of the adjustment may appear, depending on the operating environment of the MFP. Therefore,

carefully perform the adjustment, while checking the copy or print image.

Remarks

• The effect of the adjustment may vary, depending on the usage pattern of the consumables, such as the

developer material and drum, and the operating environment of the MFP.

• When replacing any consumable, refer to the relevant information in the Service Manual and Service Handbook.

1. General Adjustments – Copying, Printing and e-Filing (Output from Box)

Содержание e-studio 2330C

































































































































































































































































Результаты поиска

Содержание e-studio 2330C

Отзывы:

Похожие инструкции для e-studio 2330C

Бренды по названию

Популярные бренды

Toshiba e-studio 2330C, Руководство по визуализации

Результаты поиска

Содержание e-studio 2330C

Отзывы:

Похожие инструкции для e-studio 2330C

Бренды по названию

Популярные бренды