TigerStop TigerSaw 1000 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 68

background image

48

Printer Adjustments

The TigerSaw 1000 evolution ink jet printer has a height adjustment to control the height of the print

printer head. It is critical that the printer be as close to the material as possible.

Printer Height Adjustment

To adjust printer height...
1. Put a piece of material under the printer head.
2. Loosen the locking handle and allow the printer wheel to touch your material.
3. Raise the printer by about .125 inch or less.
4. Tighten the locking handle.

Note: Printer height is critical to print quality.

Cleaning the Printer

The evolution ink jet printer has disposable ink cartridges that house the ink jets. The ink jets can

be cleaned if necessary.

To clean the printer...
1. Simply use a dry paper towel and wipe the printer ink jets in a motion parallel to the ink jets.
2. If the print quality is still low, you may need to change the ink cartridge.

UV Sensor Adjustment

The UV sensor on the TigerStop pusher foot can be adjusted in both sensitivity and sensor height.

Locking Handle

«
...
49
50
51
52
53
...
»

Содержание TigerSaw 1000





































































Отзывы:

Нет отзывов

Похожие инструкции для TigerSaw 1000

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: JAC Страницы: 100

Бренд: Taylor Страницы: 70

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: Datavideo Страницы: 48

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 3

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 8

Бренд: Datavideo Страницы: 10

Бренд: Garelick Страницы: 4

Бренд: Idmed Страницы: 2

Бренд: Omlet Страницы: 60

Бренд: Haas Страницы: 12

Бренд: SaMASZ Страницы: 25

Бренд: Waterpik Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды