TigerStop TigerSaw 1000 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 68

background image

46

Adjusting Flow to the Saw Blade Cylinder

The cylinder that controls the saw blade travel has a flow adjustment on both cylinder ports. This

will speed up or slow down the saw cycle.

Note: Always power down and follow all lockout/tag out procedures before opening any saw access door.

To access the saw blade cylinder...
1. Loosen the bolts holding the access cover.
2. Lift up and pull the cover away.

Adjusting Flow to the Pusher Foot Cylinder

The TigerSaw 1000 pusher foot uses an air cylinder to raise and lower the foot during operation.

This cylinder has flow adjustments on both ports. This will speed up or slow down the pusher foot.

Saw Blade Adjustment Points

TigerSaw 1000 has adjustments for saw blade square and saw cycle height. Ensure TigerSaw is

properly locked out/tagged out before performing any adjustments.

Blade Square Adjustment

TigerSaw as an adjustment to change the square of the saw blade to the back fence. This adjust-

ment is located on the back of the saw table.

This can be adjusted by loosening bolt A and bolt B. Then rotate peg C. Once the adjustment has

been made, tighten bolt A and B.

«
...
47
48
49
50
51
...
»

Содержание TigerSaw 1000





































































Отзывы:

Нет отзывов

Похожие инструкции для TigerSaw 1000

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: AccuMed Страницы: 14

Бренд: TAS Страницы: 25

Бренд: made for movement Страницы: 51

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Nederman Страницы: 255

Бренд: VARISCO Страницы: 24

Бренд: Vari Lite Страницы: 14

Бренд: Vaniman Страницы: 3

Бренд: Baileigh Industrial Страницы: 12

Бренд: Fast Страницы: 60

Бренд: Y.I.C. TECHNOLOGIES Страницы: 6

Zen-O lite RS-00600

Бренд: GCE Страницы: 20

Бренд: GE Страницы: 644

Бренд: Econo-Wrap Страницы: 27

Бренд: Hatco Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды