TigerStop TigerSaw 1000, Руководство по установке

Страница: 4 / 68

•Any Automatic equipment can be dangerous if used improperly, and this includes TigerStop and its line of automation
equipment: TigerStop, TigerPro, TigerFence (standard and SLR), TigerCrossCut, TigerTurbo, TigerRack, Heavy Duty2 and
TigerSaw.
•But before you put your tape measure away and start making a TigerStop machine your newest best friend, please read
and consider the following safety reminders, some of which may relate to the operation of your other power tools as well.
•If a warning is also found elsewhere in this manual or on a label affixed to the machine, the reference is shown in paren-
theses.
Warning: TigerStop, TigerFence, TigerCrossCut, TigerRip Fence, Heavy Duty2, TigerTurbo and TigerRack are
machine components intended for use in conjunction with other potentially dangerous machinery. The use of
these components does not make that machinery safe. TigerStop, LLC’s products are not intended to substitute,
in any manner, for safety requirements in general, or in conjunction with other safety features to make the
machine as safe as possible and to ensure that it meets federal, state and local law with respect to safety and all
other regulatory requirements. In addition, TigerStop, TigerStop Heavy Duty 2, and TigerTurbo are machine com-
ponents that should only be operated by qualified persons trained in safe operating procedures. Illustrations of
TigerStop, TigerStop Heavy Duty2 and TigerTurbo components in use do not show, and are not intended to show,
safety features necessary to make the machinery safe to operate.
(Label covering end cap of fence extrusions)
Warning: TigerStop (TigerFence SLR, TigerFence, TigerCrossCut, TigerTurbo, TigerRack, Heavy Duty2 and
TigerSaw) must be installed in accordance with all local, state, and federal regulations, as well as common
sense safety requirements, Use only trained professionals when installing TigerStop machines with existing
equipment to ensure a safe and proper work station that will in no way endanger the operator or any other per-
sonnel. Do not operate without proper training, both in TigerStop operation, and in the operation of adjoining
equipment.
(Installation Guides of: TigerStop, TigerFence, TigerFence SLR, TigerCrossCut, TigerTurbo, TigerRack and
Heavy Duty2)
FOUR IMPORTANT CAUTIONS:
1. Do not randomly drill and tap holes in the TigerStop fence beam for mounting or for any other purpose. This might damage the
drive system. All fastening or attachment to the fence beam MUST be made by inserting T-bolts or T-nuts WITH washers!
2. It is CRITICAL - especially if NOT using TigerStop attachment brackets (UBR), that if T-nuts are used, the bolts are prevented
from tightening through them and into the aluminum fence beam. Again, it is imperative that washers be used.
3. Uneven tightening of the bolts used to fasten down TigerStop to its mounting support can introduce a slight twist or other defor-
mation in the beam. This will result in inaccurate measurement and premature failure of the drive belt or other components.
4. The motor box (compartment) contains DC voltage with potentially FATAL amperage. NEVER attempt any unauthorized actions
inside the motor box.
(linked from TigerStop Installation, Feed Table Installation, Ledge Stand)
CAUTION: NEVER drill holes into the HD2 fence beam for any reason!
(HD2 Installation)
CAUTION: NEVER drill holes into the TigerTurbo fence beam for any reason!
(TigerTurbo Installation)
CAUTION: Washers MUST be used to prevent damage to the fence beam by over tightening!
(Mounting TigerStop to a Feed Table)
WARNING: Using a TigerStop interconnect does not relieve you of the responsibility for making sure that
your saw or other tool has all the necessary safety equipment in place.
(Standard Interconnect Kit, Advanced Interconnect Kit)
DANGER: This machine can start, move and stop automatically. Keep hands and loose clothing clear of moving
parts while operating. Moving parts can crush and cut. When used with a saw or other cutting equipment, bodily
injury and death may result if operated without safety guards on all machines. Do not operate with guards
removed. Operators must wear adequate eye and ear protection. High voltage DANGER - Do not open motor
compartment or controller keypad. No user serviceable parts inside.
(TigerStop Quick Reference Card, ALSO label of motor end plate or amplifier cover)
Safety First!