TigerStop TigerSaw 1000 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 68

background image

57

TigerSaw Troubleshooting

TigerSaw 1000 Crayon Marking Troubleshooting

TigerSaw 1000 Printer Troubleshooting

Problem

Solution

The saw blade access door will not open.

TigerSaw will lock the saw blade access door
when the saw motor is on. Remove power and
lock out/tag out TigerSaw. The door will unlock
when power is off.

The saw guard door will not open.

TigerSaw will lock the guard door when the saw
motor is on. Turn off the saw motor and the door
will unlock. The saw motor cannot be powered
up until the guard door is closed.

TigerSaw will not turn on or saw blade motor will
not turn on.

The blade motor cannot be turned on unless all
of the safety interlocks are engaged and reset.
Check all interlocks and ensure they are
engaged and reset as shown in “Basic TigerSaw
Operation”, p.45.

TigerSaw is screeching or making noise as it
runs.

Inspect and tighten the saw belt as shown in
“Removing the saw belt”, p.59.

Cut parts are not square.

The saw blade square can be adjusted as
shown in “Blade square adjustment”, p.59

Cut quality is poor

See Appendix A: “Factors Affecting Cut Quality”.

Problem

Solution

TigerSaw is not seeing crayon marks or not see-
ing the stock.

Adjust the UV and IR sensors as shown in
“Adjustment Points”, p.50.

TigerSaw is not cutting my defects accurately

Adjust the pusher foot offset and infrared offset
as shown in “Setup”, p.33.

Problem

Solution

TigerSaw is not printing

Set the printer type setting as shown in “Setup”,
p.33. Then return to the Ready Screen and wait
for 20 seconds. TigerSaw will then automatically
connect to the printer. Remove printer cartridge
and clean connection pins.

Print quality is bad.

Adjust the printer height and clean the printer
cartridge as shown in “Adjustment Points”, p.50.
If problem persists, replace printer cartridge.

The printing is not in the proper place on the
part or the print was cut by the saw blade.

Adjust the ink jet offset setting as shown in
“Setup” p.33.

«
...
58
59
60
61
62
...
»

Содержание TigerSaw 1000





































































Отзывы:

Нет отзывов

Похожие инструкции для TigerSaw 1000

Giraffe OmniBed

Бренд: Ohmeda Страницы: 54

Бренд: Datavideo Страницы: 50

Бренд: Waterous Страницы: 90

Бренд: Campbell Страницы: 14

Бренд: NEC Страницы: 44

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Hardt Страницы: 22

Бренд: Sabre Страницы: 2

Бренд: National Instruments Страницы: 10

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

LED Street Bar 16x3W RGB IP65

Бренд: Varytec Страницы: 9

Бренд: VARILITE Страницы: 8

EVENTPROFILE VL800

Бренд: Vari Lite Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды