TigerStop TigerSaw 1000 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 68

background image

47

Warning! Do not take out bolts A and B. Doing so will damage TigerSaw!

Adjust Cycle Height

TigerSaw 1000 has two sensors mounted to the saw cycle cylinder. The top sensor controls saw

cycle height. Ensure TigerSaw is properly locked out/tagged out before performing any adjustments.

1. Open the side access door and locate the saw cycle cylinder.
2. This cylinder has 2 sensors attached to it.
3. Loosen one of the screws holding the top sensor tight to the cylinder.
4. Move the sensor up or down.
5. Tighten the screw once the sensor is in place.

The sensor lights up when it senses the saw blade. Watch the light for the few first cycles. If the

light is yellow, it means that the sensor is on the edge of its sensing range. Adjust the sensor sideways
until this light is green.

Top Cap Travel Adjustment

The range of movement on the top cap can be adjusted to suit the material you are cutting.

To adjust the top cap travel...
1. Turn the saw blade off using the red portion of the power switch marked “Saw”.
2. Loosen the locking handle as shown.
3. Turn the height adjustment wheel to adjust the top cap stopper.
4. Power the saw blade up to apply air pressure and test the top cap travel.
5. Repeat if necessary.

«
...
48
49
50
51
52
...
»

Содержание TigerSaw 1000





































































Отзывы:

Нет отзывов

Похожие инструкции для TigerSaw 1000

Бренд: UnionSpecial Страницы: 56

MicroVersaTrip Plus

Бренд: GE Страницы: 20

MicroVersaTrip Plus

Бренд: GE Страницы: 2

Бренд: GE Страницы: 252

Бренд: Balanced Body Страницы: 12

Бренд: Eagle Pro Страницы: 6

Бренд: GE Страницы: 10

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: Xiitech Страницы: 6

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

Бренд: OHAUS Страницы: 84

Бренд: VADDIO Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды