manualshive.com logo in svg

Thermo King SR-2 SmartReefer2, Руководство по диагностике


Поделиться
Скачать
background image

Section 3 – SR-2 Software Description 

 

Unit Configuration Setup Menu 

The Unit Setup Menu is used to specify the actual 
unit configuration.  These features are set at the 
factory as required for each unit.  The factory 
settings shown below are for a replacement 
microprocessor. 
 

Alarm Code 111 Unit Not Configured Correctly 

 

 

If the microprocessor detects a mismatch between 
unit connections and configuration selections, Alarm 
Code 111 Unit Not Configured Correctly will be set. 
 
 

Engine Type Is 
Micro Rev 

All 

HMI Rev 

All 

Choices 

 

Factory Set 

Yanmar 2.1 

Exceptions 

 

Description

 

This feature allows the engine type 

to be selected.  Currently only Yanmar 2.1 is 
available. 
 
 

Compressor Type Is 
Micro Rev 

All 

HMI Rev 

All 

Choices 

Recip or Screw 

Factory Set 

Reciprocating 

Exceptions 

 

Description

 

This feature allows the compressor 

type to be selected.  The screw option is for a future 
implementation and should not be selected. 
 
 

ETV Configured 
Micro Rev 

All 

HMI Rev 

All 

Choices 

YES or NO 

Factory Set 

YES 

Exceptions 

 

Description

 

This feature allows the unit to be 

configured with an Electronic Throttling Valve (ETV).  
Units with ETV valve should be set YES.  All other 
units should be set NO. 
 

 

Electric Standby Equipped? 
Micro Rev 

All 

HMI Rev 

All 

Choices 

YES or NO 

Factory Set 

To match unit as built 

Exceptions 

 

Description

 

This feature specifies if the unit is 

equipped with optional electric standby.  If the unit is 
equipped with electric standby, this feature should 
be set Yes.  If the unit is not equipped with electric 
standby, this feature should be set No. 
 
 

Electric Motor Type Is 
Micro Rev 

All 

HMI Rev 

All 

Choices 

2 Pole or 4 Pole 

Factory Set 

4 Pole 

Exceptions 

The 2 pole is a future option and 

should not be selected 

Description

 

Current units with electric standby 

should be set for a 4-pole motor. 
 
 

Diesel to Electric Auto Switch Enabled? 
Micro Rev 

All 

HMI Rev 

All 

Choices 

YES or NO 

Factory Set 

NO 
 

Exceptions 

 

Description

 

This feature allows the Auto Switch 

from Diesel to Electric to be enabled or disabled.  If 
this feature is set YES, the unit will switch 
automatically to electric mode when standby power 
is connected.  If the feature is set NO, the operator 
must physically switch the unit to electric mode. 

 

3-44 

31 January 2005 
 

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR-2 SmartReefer2

Palfinger V Series Fitting Instructions Manual preview
V Series
Бренд: Palfinger Страницы: 34
Panasonic CZ-RTC5B Installation Instructions Manual preview
CZ-RTC5B
Бренд: Panasonic Страницы: 15
Panasonic CZ-RTC3 Operating Instructions Manual preview
CZ-RTC3
Бренд: Panasonic Страницы: 42
QCON ProX Setup preview
ProX
Бренд: QCON Страницы: 4
Jetline 9600 Series Operation Manual preview
9600 Series
Бренд: Jetline Страницы: 58
Samson 3277 Mounting And Operating Instructions preview
3277
Бренд: Samson Страницы: 48
National Instruments NI 9215 Calibration Procedure preview
NI 9215
Бренд: National Instruments Страницы: 8
olympia electronics GR-6500 Quick Installation Manual preview
GR-6500
Бренд: olympia electronics Страницы: 10
Warner Electric RFC-100 Service & Installation Instructions preview
RFC-100
Бренд: Warner Electric Страницы: 4
Safety Clamps VL-BC Operation, Maintenance, And Repair Manual preview
VL-BC
Бренд: Safety Clamps Страницы: 16
Case IH MAXXUM 100 Service Manual preview
MAXXUM 100
Бренд: Case IH Страницы: 81
GE 41567 Instruction Manual preview
41567
Бренд: GE Страницы: 32
SystemAir SYSVRF AHU 10HP S Installation & Owner'S Manual preview
SYSVRF AHU 10HP S
Бренд: SystemAir Страницы: 16
Zapi COMBI SEM-1 Operating And Users Manual preview
COMBI SEM-1
Бренд: Zapi Страницы: 30
Webasto SmarTemp Control fx Installation And Operation Instructions Manual preview
SmarTemp Control fx
Бренд: Webasto Страницы: 8
National Instruments SCXI-1181K Installation Manual preview
SCXI-1181K
Бренд: National Instruments Страницы: 4
Keithley MSSR-32 Packing List preview
MSSR-32
Бренд: Keithley Страницы: 3
Zamel EXTA LIFE P-520 Manual preview
EXTA LIFE P-520
Бренд: Zamel Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды