manualshive.com logo in svg

Thermo King SR-2 SmartReefer2, Руководство по диагностике


Поделиться
Скачать
background image

Section 2 – SR-2 Hardware Description 

 

 

HMI CONTROL PANEL 

The HMI (Human Machine Interface) Control Panel 

consists of an LCD graphics display screen and 

eight touch sensitive keys.  The four keys on the 

sides of the control panel are used to turn the unit on 

and off, initiate a manual defrost cycle, and select 

the desired operating mode.  The function of the four 

keys located below the display screen change as 

required by the current menu.  These are known as 

software controlled keys or ‘soft keys’.  The current 

function of the key is controlled by software and 

displayed directly above the key. 

 

S

mart

R

eefer

2

OFF

ON

MENU

35

°F

35

CYCLE SENTRY

SET

SENSORS

GAUGES

POINT

.8

 

HMI Control Panel 

 

The display screen is used by the microprocessor to 

provide visual prompts and information to the 

operator, such as operating mode, setpoint, gauge 

and hourmeter readings and operating conditions of 

the diesel engine.  Information can be displayed in 

21 possible languages.  A single version of software 

can display a maximum of 11 languages.  The HMI 

also contains the Cargo Watch Data Logger.  The 

HMI and microprocessor communicate via a CAN 

(Controller Area Network) connection. 

 

If the HMI Control Panel is disconnected from the 

unit while the unit is running, the unit will shut down.  

The unit will not restart when the HMI Control Panel 

is reconnected until the On key is pressed. 

 

See Section 4 for complete HMI control panel 

operating details. 

 

Real Time Clock 

The real time clock is located in the HMI Control 

Panel.  The time is supplied to the microprocessor 

each time the unit is turned on.   

 

Clock Power 

The HMI control panel features a capacitor to 

provide backup power to the real time clock.  This 

capacitor is capable of maintaining the clock for 

approximately two weeks with no power connected 

to the unit.  The capacitor is recharged any time the 

HMI control panel is installed in the unit and the 

Microprocessor Power Switch is turned on. 

 

If the unit Microprocessor Power Switch is turned off 

or the unit battery is disconnected for an extended 

period the clock setting should be checked when the 

unit is returned to service.  If the HMI Control Panel 

is changed the clock setting should also be verified. 

 

2-6 

31 January 2005 

 

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR-2 SmartReefer2

ABATEC A1 Installation And Operation Instruction Manual preview
A1
Бренд: ABATEC Страницы: 8
NEC Univerge SV9100 Hardware Manual preview
Univerge SV9100
Бренд: NEC Страницы: 478
NEC Univerge UM8000 General Description Manual preview
Univerge UM8000
Бренд: NEC Страницы: 46
NEC NEAX 2400 ICS Manual preview
NEAX 2400 ICS
Бренд: NEC Страницы: 149
NEC LED-E012i User Manual preview
LED-E012i
Бренд: NEC Страницы: 13
Samsung SolarCell Remote Operating Instructions preview
SolarCell Remote
Бренд: Samsung Страницы: 2
Aastra Ascotel Office 45 Operating Instructions Manual preview
Ascotel Office 45
Бренд: Aastra Страницы: 40
Aastra OpenCom 100 Mounting And Commissioning User Manual preview
OpenCom 100
Бренд: Aastra Страницы: 244
Aastra 632d Quick User Manual preview
632d
Бренд: Aastra Страницы: 30
Aastra 5380 Quick User Manual preview
5380
Бренд: Aastra Страницы: 24
Aastra IntelliGate A150 System Manual preview
IntelliGate A150
Бренд: Aastra Страницы: 524
Aastra Ascotel IntelliGate 150 System Manual preview
Ascotel IntelliGate 150
Бренд: Aastra Страницы: 228
Accu-Sort RFR-02 Test Procedure preview
RFR-02
Бренд: Accu-Sort Страницы: 22
Sanhua MDF Series Instructions preview
MDF Series
Бренд: Sanhua Страницы: 3
rav KT100 Operating Instructions Manual preview
KT100
Бренд: rav Страницы: 120
K'Nex Education 79018 User Manual preview
79018
Бренд: K'Nex Education Страницы: 56
Taoglas EDGE Locate Quick Start Manual preview
EDGE Locate
Бренд: Taoglas Страницы: 2
WAGO I/O SYSTEM 750 Quick Start Manual preview
I/O SYSTEM 750
Бренд: WAGO Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды