manualshive.com logo in svg

Thermo King SR-2 SmartReefer2, Руководство по диагностике


Поделиться
Скачать
background image

Section 2 – SR-2 Hardware Description 

 

 

MICROPROCESSOR 

The SR2 microprocessor is located on the rear 

panel of the control enclosure.  Two multi-pin 

interface board connectors (J1 and J2) are located 

on the front of the microprocessor.  A 37 pin sensor 

connector (J3) is located at the lower left of the 

microprocessor.  The J3 connector is used for 

sensor inputs. 

      

J1

J2

J3

ASS'Y P/N: 1E19311G01
S.P. P/N: 45-2015
S/N:XXXXXXXXXXX

REV. B000

ASS'Y P/N: 1E19308G01
S.P. P/N: 45-2013
S/N:XXXXXXXXXXX

REV. B000

A ND

C

 

SR2 Microprocessor.   

The J1 and J2 connectors are used to mate the 

microprocessor and interface board into a  

single assembly. 

Microprocessor Operation 

The microprocessor is the heart of the control 

system.  It consists of the microprocessor, software, 

memory, inputs and outputs.  The software provides 

the required operating and control functions and 

supports the Service Watch Data Logger. 

 

Inputs are used to supply power and system 

information to the microprocessor.  The 

microprocessor uses the outputs to control the 

operation of the unit components.  The 

microprocessor has no user serviceable 

components. 

 

Real Time Clock 

The real time clock is located in the HMI Control 

Panel.  The time is supplied to the microprocessor 

each time the unit is turned on.  If the 

microprocessor is changed the clock setting will be 

automatically supplied to the microprocessor when 

the unit is turned on. 

 

Programmable Features 

The settings of all programmable features are held 

in non-volatile memory in the microprocessor.  The 

settings are supplied to the HMI Control Panel each 

time the unit is turned on.  If the microprocessor is 

changed, all programmable features must be 

reprogrammed. 

2-9 

31 January 2005 

 

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR-2 SmartReefer2

Wavetec Spectra Installation Manual preview
Spectra
Бренд: Wavetec Страницы: 17
Calsense ET1 Manual To Programming preview
ET1
Бренд: Calsense Страницы: 9
MaestroHome Smart Controller Quick Setup Manual preview
Smart Controller
Бренд: MaestroHome Страницы: 10
ZIMO MX10 Instruction Manual preview
MX10
Бренд: ZIMO Страницы: 38
B meters IWM-LR4 Quick User Manual preview
IWM-LR4
Бренд: B meters Страницы: 2
Ebyte E103-W03 Product Instruction Manual preview
E103-W03
Бренд: Ebyte Страницы: 38
EBS CPX200NB User Manual preview
CPX200NB
Бренд: EBS Страницы: 30
Ebyte E180-Z5812SP Product Manual preview
E180-Z5812SP
Бренд: Ebyte Страницы: 35
ICP DAS USA PCI-D64HU Quick Start Manual preview
PCI-D64HU
Бренд: ICP DAS USA Страницы: 7
ICP DAS USA I-2533CS Series Quick Start Manual preview
I-2533CS Series
Бренд: ICP DAS USA Страницы: 8
Valcom V-2003A Technical Specifications preview
V-2003A
Бренд: Valcom Страницы: 3
Valcom V-1092 User Manual preview
V-1092
Бренд: Valcom Страницы: 3
Valcom V-1092 Technical Specifications preview
V-1092
Бренд: Valcom Страницы: 2
OJ Electronics OJ-Air2-WP55 Instructions Manual preview
OJ-Air2-WP55
Бренд: OJ Electronics Страницы: 8
GI.BI.DI AS05582 Installation Instructions Manual preview
AS05582
Бренд: GI.BI.DI Страницы: 60
Tormatic DuoControl Signal 111 Quick Start Manual preview
DuoControl Signal 111
Бренд: Tormatic Страницы: 3
M-system R7F4DC-DA16A-H Instruction Manual preview
R7F4DC-DA16A-H
Бренд: M-system Страницы: 7
jbc HDE-9UD Instruction Manual preview
HDE-9UD
Бренд: jbc Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды