Thermo King SR-2 SmartReefer2 Скачать руководство пользователя страница 23

Страница: 23 / 431

Section 2 – SR-2 Hardware Description

Programmable Features

Display Heater

The settings of all programmable features are held

in non-volatile memory in the microprocessor. The

settings are supplied to the HMI Control Panel each

time the unit is turned on. If the HMI Control Panel

is changed, the current programmable feature

settings will be supplied to the HMI Control Panel

when the unit is turned on.

The HMI control panel is equipped with a display

heater. This heater is needed to make the display

visible in cold ambient temperatures.

The HMI has its own internal temperature sensor for

the display heater. The heater is energized when

the unit is turned on and the ambient temperature is

below 29.4°F (-2°C). The heater turns off when the

temperature sensed by the internal sensor rises

above 37.4°F (+3°C). The heater draws from 1.4 to

1.7 amps when energized.

Fuse F10

When interface board fuse F10 is installed in the

upper position, the On/Off keys on the HMI turn the

unit on and off. When fuse F10 is installed in the

lower position the unit will start and run without the

HMI control panel. Do not operate the unit with the

F10 fuse installed in the lower position unless

absolutely necessary.

The colder the ambient temperature the longer it will

take for the heater to make the display visible on a

cold startup. It may take 10-15 seconds for the

display to appear with very cold temperatures.

2-7

31 January 2005

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Результаты поиска

Содержание SR-2 SmartReefer2

Отзывы:

Похожие инструкции для SR-2 SmartReefer2

Бренды по названию

Популярные бренды

Thermo King SR-2 SmartReefer2, Руководство по диагностике

Результаты поиска

Содержание SR-2 SmartReefer2

Отзывы:

Похожие инструкции для SR-2 SmartReefer2

Бренды по названию

Популярные бренды