manualshive.com logo in svg

Thermo King SR-2 SmartReefer2, Руководство по диагностике


Поделиться
Скачать
background image

Section 3 – SR-2 Software Description 

 

Continuous Mode OptiSet Features - 
Fresh Ranges with ETV and Modulation 
On 

 
The features shown below can be modified in 
Continuous Mode operation with Fresh ranges on 
units equipped with ETV and with Modulation turned 
on.  Continuous Mode features are different for 
Frozen ranges or for Fresh ranges on units that are 
not equipped with ETV or if Modulation is turned Off. 

 

 

 

FreshSet™ 

FreshSet is an additional set of configurable 
parameters within the OptiSet program tailored for 
Fresh Produce.  It is applicable for ETV based units 
using the Continuous Run mode.  
 
FreshSet allows modulation temperature control to 
be configured with a Floor Limit and High Speed 
Modulation Ceiling (temperature band). 
 
The refrigeration unit will operate in low speed to 
keep discharge air temperature and return air 
temperature within these bands.  If the refrigeration 
unit is unable to maintain the band it will 
automatically force the unit into high speed 
operation until the temperature band requirements 
are met.  High ambient temperatures, poor trailer 
insulation and product loaded warm are potential 
causes that could force the unit to run in high speed 
for a period of time. 
 
 
 
 
 

 

Modulation Control 
Micro Rev 

All 

HMI Rev 

All 

Choices 

Off or On 

Factory Set 

On 

Exceptions 

 

Description

 

This feature allows Modulation to be 

turned On or Off for the selected range. 
 
An ETV (Electronic Throttling Valve) capable of 
opening and closing incrementally is installed 
between the evaporator

 

and the compressor.  If 

modulation is turned On, the ETV is controlled 
directly by the microprocessor.  As the temperature 
approaches setpoint, the ETV begins to close, 
throttling the suction gas returning to the compressor 
and thus reducing cooling capacity.  As the box 
temperature approaches setpoint, the ETV becomes 
more nearly closed.  This feature provides very 
smooth and steady temperature control.  Modulation 
is only operational in Continuous mode. 
 
The normally closed hot gas solenoid is opened 
during modulated cool when the temperature is very 
close to setpoint.   This diverts hot gas from the 
compressor discharge line, through the open hot 
gas solenoid to the evaporator distributor, in order to 
further reduce cooling capacity and prevent the 
compressor from operating in a vacuum. 
 

3-36 

31 January 2005 
 

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR-2 SmartReefer2

VAT 168 Series Installation, Operating, & Maintenance Instructions preview
168 Series
Бренд: VAT Страницы: 29
Balboa Instruments Dolphin Manual preview
Dolphin
Бренд: Balboa Instruments Страницы: 19
Yardney Synergy Quick Start Manual preview
Synergy
Бренд: Yardney Страницы: 8
Eaton TS110 Product Manual preview
TS110
Бренд: Eaton Страницы: 28
Parallel Galleon Installation Manual preview
Galleon
Бренд: Parallel Страницы: 16
V2 EASY Series Manual preview
EASY Series
Бренд: V2 Страницы: 46
Jands SafeGuard Installation Manual preview
SafeGuard
Бренд: Jands Страницы: 7
hager coviva Smartbox TKP100A Operation And Configuration Instructions preview
coviva Smartbox TKP100A
Бренд: hager Страницы: 34
Eaton S611 User Manual preview
S611
Бренд: Eaton Страницы: 96
Gardena 8200-20 Operator'S Manual preview
8200-20
Бренд: Gardena Страницы: 236
M-system R3-PD16B Instruction Manual preview
R3-PD16B
Бренд: M-system Страницы: 10
East Coast Datacom DMM-X21 Operation Manual preview
DMM-X21
Бренд: East Coast Datacom Страницы: 14
Brähler Systems 05.0055 Instruction Manual preview
05.0055
Бренд: Brähler Systems Страницы: 25
Monster Central REVOLUTION 200 Instruction Manual preview
REVOLUTION 200
Бренд: Monster Central Страницы: 13
Rain Bird ESP-RZXe Installation And Operation Manual preview
ESP-RZXe
Бренд: Rain Bird Страницы: 18
Easy Lift Equipment EAGLE GRIP EG4MDC2-F Operating And Maintenance Manual preview
EAGLE GRIP EG4MDC2-F
Бренд: Easy Lift Equipment Страницы: 17
Dantherm HRC 2 User Manual preview
HRC 2
Бренд: Dantherm Страницы: 28
N-Com BX4 PLUS User Instructions And Safety preview
BX4 PLUS
Бренд: N-Com Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды