manualshive.com logo in svg

Thermo King SR-2 SmartReefer2, Руководство по диагностике


Поделиться
Скачать
background image

Section 3 – SR-2 Software Description 

 

SOFTWARE OPERATION 

MENU STRUCTURE 

 

 

The basic menu structure consists of three menus 
plus the Temperature Watch

®

 screen.  See the 

following material for a general description of each 
menu.  See Section 4 for complete operating 
instructions. 

Software is a very complex set of instructions used 
by the microprocessor to control the refrigeration 
and interface with the operator.  The microprocessor 
examines the conditions of all the inputs and 
compares them to the instructions contained in the 
software.  The outputs are then energized as 
specified by the software instructions.   

 

•

 The 

Temperature Watch Display

 shows the 

box temperature and setpoint using large 
numbers that allow unit conditions to be 
checked from a distance. 
 

 
There is no way to determine from the schematic 
what conditions will cause the unit to operate in a 
particular mode.  This decision is made by the 
microprocessor and software after examining all the 
input conditions and setpoint.  However, operating 
mode can usually be deduced from the existing 
conditions.  As an example, if a 35°F (2°C) setpoint 
is selected and the box temperature, as indicated by 
the return air sensor is 60°F (16°C), the unit should 
operate in Cool mode when turned on.   

•

 The 

Main Menu

 is made up of menu items 

intended for the driver or unit operator.  The 
Main Menu is directly accessible from the 
Standard Display using the soft keys at the 
bottom of the display    

 

•

 The 

Maintenance Menu

 is made up of menu 

items used to help the service technician 
maintain and diagnose the unit.  The 
Maintenance Menu is indirectly accessible from 
the Main Menu. 

 

 
The SR-2 system requires two versions of software.  
The microprocessor software is used for all 
operational functions.  The HMI software controls 
the display screens and operator interface. 
 

•

 The 

Guarded Access Menu

 is made up of 

programmable features that configure the unit, 
set sensor grades and allow the customer to 
tailor unit operation to his particular 
requirements.  The Guarded Access Menu is 
indirectly accessible from the Maintenance 
Menu. 

 
 
 

The software is flashloaded using a PC computer.  
See Service Procedure A46A and A46B for details. 
 
To check software revision of the microprocessor 
and HMI control panel refer to Section 4 of this 
manual. 
 

 

 

3-5 

31 January 2005 
 

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR-2 SmartReefer2

ABB REC650 ANSI Applications Manual preview
REC650 ANSI
Бренд: ABB Страницы: 370
ABB EAN823 Instructions Manual preview
EAN823
Бренд: ABB Страницы: 17
ABB COM600 series User Manual preview
COM600 series
Бренд: ABB Страницы: 104
ABB AC 800M Library Object Style Manual preview
AC 800M
Бренд: ABB Страницы: 120
ABB ABILITY SSC600 Product Manual preview
ABILITY SSC600
Бренд: ABB Страницы: 42
Hankscraft Runxin HD Series Service Manual preview
HD Series
Бренд: Hankscraft Runxin Страницы: 53
Panasonic FP0 Series Specifications preview
FP0 Series
Бренд: Panasonic Страницы: 27
Panasonic CZ-64ESMC2 Instruction Manual preview
CZ-64ESMC2
Бренд: Panasonic Страницы: 78
Panasonic GM1 Series Reference Manual preview
GM1 Series
Бренд: Panasonic Страницы: 98
NAiS FP0 Series Hardware Manual preview
FP0 Series
Бренд: NAiS Страницы: 173
Panasonic SL-VGU1-EC Instruction Manual preview
SL-VGU1-EC
Бренд: Panasonic Страницы: 2
BADLANDS LE-03 Quick Manual preview
LE-03
Бренд: BADLANDS Страницы: 2
Gardena 4030 Operating Instructions Manual preview
4030
Бренд: Gardena Страницы: 17
SAFI DN15 Manual preview
DN15
Бренд: SAFI Страницы: 18
Badger Meter Orion Series Quick Start Manual preview
Orion Series
Бренд: Badger Meter Страницы: 2
Badger Meter MDS 2000 Installation And Software Manual preview
MDS 2000
Бренд: Badger Meter Страницы: 48
Badger Meter BadgerTouch HREBT Manual preview
BadgerTouch HREBT
Бренд: Badger Meter Страницы: 12
Badger Meter CB-30 User Manual preview
CB-30
Бренд: Badger Meter Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды