Thermo King SR-2 SmartReefer2 Скачать руководство пользователя страница 28

Страница: 28 / 431

Section 2 – SR-2 Hardware Description

Interface Board Fuse Size & Function

Fuse Size

Function

HPCO Switch Circuit

F2 15A

2AB

Power

40A

Fuel Sol Pull-In/Starter Circuit

F4 None

No fuse - all Bosch alternators

2A fuse - all Prestolite alternators

F5 60A

Preheat

Circuit

15A

Damper and High Speed Circuits

8FP Circuit – CAN bus

CAN Connector J12

CAN Connector J14

F10

10A

8X Power - install in upper position

F11

10A

Electric Clutch (Not Used)

F12

CAN Connector J13

F13

8FC Circuit (Remote Lights)

F15

P/S

On/Off Relay

F20 2A

Alternator

Sense

F22

Not

Used

F23

Not

Used

Note 1 - The F4 must be in place for Prestolite

alternators to charge. It must be removed for Bosch

alternators. Note: Service parts interface boards

are shipped without F4 fuse.

F10

There are three in-line fuse clips that allow for

two configurations of the F10 fuse. The upper

position is the normal position. When fuse F10 is

installed in the upper position, control power is

routed to the K9 On/Off Relay contacts. The On/Off

keys on the HMI control panel energize and de-

energize the K9 On/Off Relay. When the K9 On/Off

Relay is energized power is supplied through the

normally open K9 contacts to turn the unit on.

When fuse F10 is installed in the lower position

power bypasses the K9 On/Off relay contacts and

the unit will start and run without the HMI control

panel. Do not operate the unit with the F10 fuse

installed in the lower position unless absolutely

necessary.

IMPORTANT

If fuse F10 is installed in the lower position the

unit will start and run. The HMI Control Panel On

and Off keys will not function. The Off key will

not turn the unit off if Fuse F10 is in the lower

position. If Fuse F10 is in the lower position it

must be removed or the Microprocessor Power

Switch must be turned off to turn the unit off.

F15

The device identified as F15 is a poly switch.

This overcurrent device resets automatically and is

not replaceable.

Interface Board Relay Functions

Important: Do not attempt to remove the relays

from the interface board.

Relay Function

K1 Run

Relay

K2 Preheat

Relay

High Speed Relay

K4 Damper

Relay

K5 Diesel/Electric

Relay

Fuel Solenoid Pull-In Relay

K7 Starter

Relay

Electric Clutch Relay

K9 On/Off

Relay

2-12

31 January 2005

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Результаты поиска

Содержание SR-2 SmartReefer2

Отзывы:

Похожие инструкции для SR-2 SmartReefer2

Бренды по названию

Популярные бренды

Thermo King SR-2 SmartReefer2, Руководство по диагностике

Результаты поиска

Содержание SR-2 SmartReefer2

Отзывы:

Похожие инструкции для SR-2 SmartReefer2

Бренды по названию

Популярные бренды