manualshive.com logo in svg

Thermo King SR-2 SmartReefer2, Руководство по диагностике


Поделиться
Скачать
background image

Section 4 – SR-2 Operation 

 

Pretrip Alarm Codes 

If an alarm occurs during a Pretrip Test the alarm code will be displayed as Pretrip Alarm XX, where XX is the 

alarm code. 

 

Alarm Codes When Switching Between Diesel and Electric 

If a shutdown alarm occurs that affects only diesel mode operation and the unit is switched to electric, the diesel 

mode shutdown alarm becomes an electric mode log alarm.  This allows the unit to run in electric mode without 

clearing the shutdown alarm that is preventing diesel mode operation.  If the unit is switched back to diesel mode, 

the alarm again become a diesel mode shutdown alarm and prevents unit operation. 

 

In the same manner, if a shutdown alarm occurs that affects only electric mode operation and the unit is switched 

to diesel, the electric mode shutdown alarm becomes a diesel mode log alarm to allow diesel mode operation.  If 

the unit is switched back to electric mode, the alarm reverts to an electric mode shutdown alarm and prevents unit 

operation.  If the unit is configured for electric to diesel autoswitch, it automatically starts and runs in diesel mode 

if an electric shutdown occurs. 

 

Clearing Alarm Codes 

Most alarm codes can be cleared conventionally from the Alarm Menu using the CLEAR key. 

 

The following control and display sensor alarm codes can only be cleared from the Maintenance Menu or 

Guarded Access Menu: 

•

 

Alarm Code 03 Check Control Return Air Sensor 

•

 

Alarm Code 04 Check Control Discharge Air Sensor 

•

 

Alarm Code 203 Check Display Return Air Sensor 

•

 

Alarm Code 204 Check Display Discharge Air Sensor 

 

The following alarm codes clear automatically. 

•

 

Alarm Code 64 Pretrip Reminder – Clears when a Pretrip Test is performed. 

•

 

Alarm Code 91 Check Electric Ready Input – Clears automatically when the unit starts running. 

•

 

Alarm Code 92 Sensor Grades Not Set – Clears when the sensor grade is changed from 5H. 

 

 

4-28  

31 January 2005 

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR-2 SmartReefer2

VAT 168 Series Installation, Operating, & Maintenance Instructions preview
168 Series
Бренд: VAT Страницы: 29
Balboa Instruments Dolphin Manual preview
Dolphin
Бренд: Balboa Instruments Страницы: 19
Echelon Excel 50 Installation Instructions Manual preview
Excel 50
Бренд: Echelon Страницы: 40
K&K M8700 Installation Instructions Manual preview
M8700
Бренд: K&K Страницы: 6
CAME ZL90 Installation Manual preview
ZL90
Бренд: CAME Страницы: 18
CAME ZN2 User Manual preview
ZN2
Бренд: CAME Страницы: 28
CAME ZG6 Original-Spare Parts preview
ZG6
Бренд: CAME Страницы: 28
CAME S0001 Quick Start Manual preview
S0001
Бренд: CAME Страницы: 4
CAME ZL90 Manual preview
ZL90
Бренд: CAME Страницы: 40
CAME CAT Series Quick Start Manual preview
CAT Series
Бренд: CAME Страницы: 26
CAME CAT Series Manual preview
CAT Series
Бренд: CAME Страницы: 34
CAME TOP Series Quick Start Manual preview
TOP Series
Бренд: CAME Страницы: 2
IAI ROBO Cylinder RCP2 Series Quick Start Manual preview
ROBO Cylinder RCP2 Series
Бренд: IAI Страницы: 5
IBM ServeRAID-MR10is User Manual preview
ServeRAID-MR10is
Бренд: IBM Страницы: 94
IBM ServeRAID-4 Ultra160 Series Installation Instructions Manual preview
ServeRAID-4 Ultra160 Series
Бренд: IBM Страницы: 20
IBM 8271 Nways Ethernet LAN Switch Manual preview
8271 Nways Ethernet LAN Switch
Бренд: IBM Страницы: 6
IBM 3174 Introduction Manual preview
3174
Бренд: IBM Страницы: 86
IBM 3745 Series Console Setup Manual preview
3745 Series
Бренд: IBM Страницы: 205

Бренды по названию

Популярные бренды

Загрузить еще бренды