manualshive.com logo in svg

Thermo King SR-2 SmartReefer2, Руководство по диагностике


Поделиться
Скачать
background image

Section 4 – SR-2 Operation 

 

Display 

 

MENU

35

°F

35

CYCLE SENTRY

SET

SENSORS

GAUGES

POINT

.8

 

The display presents information to the operator.  This 

information includes setpoint and temperature, unit operating 

information, gauge readings, temperatures and other 

information as selected by the operator.  The Standard Display 

of box temperature and setpoint is shown here.  The unit is 

running in CYCLE SENTRY Mode, has a setpoint of 35°F, and 

an actual box temperature of 35.8°F.  The down-pointing arrow 

shows the unit is cooling.  Pressing the left soft key accesses 

the SETPOINT and pressing the right soft key accesses the 

MAIN MENU.  The other two soft keys access the GAUGES 

and SENSORS menus. 

 

 

Keys 

 

Hard Keys 

The keys on either side of the display are dedicated or “hard” keys.  Their function always remains the same.  

They are described below. 

 

ON

 

This key is used to turn the unit on.  The Thermo King Logo screen appears briefly and the 

display shows the Standard Display of box temperature and setpoint.  For more information see 

“Turning the Unit On and Off” later in this section. 

OFF

 

This key is used to turn the unit off.  The unit enters the power-down sequence when this key is 

pressed.  For more information see “Turning the Unit On and Off” later in this section. 

 

 

This key is used to initiate a manual defrost cycle.  For more information see “Initiating a Manual 

Defrost Cycle” later in this section. 

 

 

This key is used to select Cycle Sentry Mode or Continuous Mode operation if allowed by 

OptiSet.  For more information see “Selecting Cycle Sentry or Continuous Mode” later in this 

section. 

 

 

 

4-4  

31 January 2005 

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR-2 SmartReefer2

Canon imageRUNNER ADVANCE C9075S PRO User Manual preview
imageRUNNER ADVANCE C9075S PRO
Бренд: Canon Страницы: 20
Baader Planetarium Steeldrive II Manual preview
Steeldrive II
Бренд: Baader Planetarium Страницы: 7
Beaphar RabbitComfort Product Information preview
RabbitComfort
Бренд: Beaphar Страницы: 2
Xantrex Trace C35 Installation And Operation Manual preview
Trace C35
Бренд: Xantrex Страницы: 56
Xantrex TrueCharge 2 Owner'S Manual preview
TrueCharge 2
Бренд: Xantrex Страницы: 2
Xantrex Freedom Sequence Owner'S Manual preview
Freedom Sequence
Бренд: Xantrex Страницы: 58
Xantrex Freedom e-GEN Checklist preview
Freedom e-GEN
Бренд: Xantrex Страницы: 4
Xantrex AGS Owner'S Manual preview
AGS
Бренд: Xantrex Страницы: 20
Mold-Masters TempMaster M2 Plus Series Quick Manual preview
TempMaster M2 Plus Series
Бренд: Mold-Masters Страницы: 2
Spirax Sarco FTC80 Installation And Maintenance Instructions Manual preview
FTC80
Бренд: Spirax Sarco Страницы: 24
Trinamic TMCM-1240 Hardware Manual preview
TMCM-1240
Бренд: Trinamic Страницы: 30
vanEE VENMAR ADVANCED TOUCHSCREEN CONTROL Installation And User Manual preview
VENMAR ADVANCED TOUCHSCREEN CONTROL
Бренд: vanEE Страницы: 4
GOAL ZERO 10 AMP User Manual preview
10 AMP
Бренд: GOAL ZERO Страницы: 52
Parker 2003-EC-00 Technical Manual preview
2003-EC-00
Бренд: Parker Страницы: 58
Brooks 5866 Installation And Operation Manual preview
5866
Бренд: Brooks Страницы: 66
Polycom RealPresence Digital Brkout User Manual preview
RealPresence Digital Brkout
Бренд: Polycom Страницы: 2
Ublox SARA-R42 Development Manual preview
SARA-R42
Бренд: Ublox Страницы: 58
Polycom EagleEye Director Quick Integration Manual preview
EagleEye Director
Бренд: Polycom Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды