manualshive.com logo in svg

Thermo King SR-2 SmartReefer2, Руководство по диагностике


Поделиться
Скачать
background image

Section 3 – SR-2 Software Description 

 

 

Sleep Mode After Pretrip  
Micro Rev 

All 

HMI Rev 

All 

Choices 

ENABLED or DISABLED 

Factory Set 

DISABLED 

Exceptions 

 

Description

 

 If the feature is set ENABLED, the 

unit will enter Sleep Mode after a Pretrip Test.  If the 
feature is set DISABLED, the unit will not enter 
Sleep Mode after a Pretrip Test.   

 

 

 
 

Rail Option 
Micro Rev 

All 

HMI Rev 

All 

Choices 

ENABLED or DISABLED 

Factory Set 

DISABLED 

Exceptions 

The optional fuel level switch must 

be installed. 

Description

 

 If the unit is a rail application, this 

feature is ENABLED.  When the optional customer 
fuel level switch closes (supplies chassis ground to 
the microprocessor fuel level input), the unit will 
enter a fuel conserve mode.  If the unit is not a rail 
application this feature should be DISABLED. 
 
 

Rail Alternate 
Micro Rev 

All 

HMI Rev 

All 

Choices 

ENABLED or DISABLED 

Factory Set 

DISABLED 

Exceptions

 

Only available if RAIL OPTION is 

ENABLED. 

Description

  This option changes the alerts 

criteria, defrost allowed temperature and defrost 
termination temperature.  It should only be used 
when specified by the customer.

   

If rail alternate is 

enabled a defrost cycle is allowed with an 
evaporator coil temperature less than or equal to 50 
°F (10°C) and terminates at 65°F (18°C).   
 

 

Blocked Air Chute Detect 
Micro Rev 

All 

HMI Rev 

All 

Choices 

ENABLED or DISABLED 

Factory Set 

DISABLED 

Exceptions 

The optional Spare Sensor 1 must 

be installed. 

Description

 

 The Air Chute Detect feature is 

designed to detect a blocked or improperly installed 
trailer air chute.  Spare sensor 1 is located at the 
rear of the trailer and directly in the air flow at the 
end of the chute.  The temperature detected by this 
sensor is compared to the temperature detected by 
the control discharge air temperature sensor.  This 
feature functions only during cool mode operation. 
 
If this temperature differential exceeds a user 
defined number of degrees for a user defined period 
of time, Alarm Code 46 CHECK AIR FLOW is 
generated as a check alarm.  If the trailer is 
equipped with a door switch and the feature is 
enabled, monitoring ceases when the door is 
opened and is resumed 45 minutes after the door is 
closed.  When the unit enters a defrost cycle, 
monitoring ceases and is resumed 45 minutes after 
the defrost cycle terminates.  Should the control 
discharge temperature sensor or Spare sensor 1 fail 
the Air Chute Detect feature is disabled. 
 
 

Temperature Differential 
Micro Rev 

All 

HMI Rev 

All 

Choices 

1°F to 20°F in 0.1°F increments 
1°C to 10°C in 0.1°C increments 

Factory Set 

9.9°F (5.5°C) 

Exceptions 

Only available if BLOCKED AIR 

CHUTE DETECT is ENABLED. 

Description

 

This feature selects the temperature 

differential, from the front to the back of the trailer 
that must be exceeded to cause an alarm to occur.  
The temperature differential is calculated using the 
control discharge air sensor and spare sensor 1.  
This temperature differential must exist for the time 
specified by TIME TO ALARM below in order to set 
Alarm Code 46 Check Air Flow. 
 

3-16 

31 January 2005 
 

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR-2 SmartReefer2

S&C 5800 Series Operating Instructions Manual preview
5800 Series
Бренд: S&C Страницы: 40
S&C 5800 Series Troubleshooting Manual preview
5800 Series
Бренд: S&C Страницы: 34
BADODOSECURITY G200 Quick Manual preview
G200
Бренд: BADODOSECURITY Страницы: 8
Hama Ni-1 Operating Instruction preview
Ni-1
Бренд: Hama Страницы: 7
Hama 12183 Operating Instruction preview
12183
Бренд: Hama Страницы: 44
RadioMaster POCKET Quick Start Manual preview
POCKET
Бренд: RadioMaster Страницы: 10
K&K M8000 Installation Instructions Manual preview
M8000
Бренд: K&K Страницы: 6
Zamel P-257/2 Quick Manual preview
P-257/2
Бренд: Zamel Страницы: 2
Zamel P-257/2 Quick Start Manual preview
P-257/2
Бренд: Zamel Страницы: 2
Zamel P-257/2 Manual Instruction preview
P-257/2
Бренд: Zamel Страницы: 2
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Бренд: Samson Страницы: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Бренд: Samson Страницы: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Бренд: Samson Страницы: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Бренд: Samson Страницы: 68
X-POWER MULTI 1 Instruction And Installation Manual preview
MULTI 1
Бренд: X-POWER Страницы: 24
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Бренд: Samson Страницы: 80
Haehne DCX Quick Start Manual preview
DCX
Бренд: Haehne Страницы: 44
Vaillant VSMART User Manual preview
VSMART
Бренд: Vaillant Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды