manualshive.com logo in svg

Thermo King SR-2 SmartReefer2, Руководство по диагностике


Поделиться
Скачать
background image

Section 4 – SR-2 Operation 

 

 

Display Self Test 

Allows the technician to perform a number of self tests on the unit HMI control panel.  The tests available are 

shown below. 

 

Choose Display Self Test by pressing the SELECT key when DISPLAY SELF TEST is shown in the Maintenance 

Menu.  The Display Self Test screen appears.  Select a test from the list below 

 

•

 

LCD Test – This test allows the technician to select a normal or inverted display.  If inverted is chosen the 

display is reversed – segments that were turned on are now turned off and segments that were turned off 

are now turned on.  The technician visually verifies that all display segments are functioning properly. 

•

 

Keypad Test – This test prompts the technician to press the four soft keys, the Defrost key and the Cycle 

Sentry key.  Each time the requested key is pressed the next prompt is displayed, allowing the technician 

to verify proper operation on these keys. 

•

 

Backlight Test – This test allows the technician to turn the backlight on and off to confirm operation. 

•

 

Brightness Test – This test allows the technician to select Low, Medium or High backlight intensity. 

•

 

Buzzer Test – This test allows the technician to turn the HMI buzzer on and off to verify operation. 

•

 

Heater Output – This test allows the technician to turn the HMI display heater on and off. 

•

 

Unit On/Off Output Test – This test allows the technician to turn the Unit On/Off output off.  This turns the 

unit off to confirm that the output can be turned off.  To restart the unit press the On key. 

•

 

SPR Digital Output Test – This test allows the technician to turn digital output 2 on and off.  This allows 

the operation of a device attached to this output to be checked. 

•

 

Serial E2 – This test allows the technician to perform an internal HMI memory test.  The test takes less 

than 1 second and the results are reported as PASS or FAIL. 

•

  Datalog Flash – This test allows the technician to perform an internal HMI CargoWatch data logger 

memory test.  The test takes less than 1 second and the results are reported as PASS or FAIL. 

•

 

RTC Update – This test allows the technician to perform an internal HMI real time clock test.  The test 

takes less than 3 seconds and the results are reported as PASS or FAIL. 

 

Evacuation Test 

Allows the technician to open all normally closed refrigeration system valves to evacuate and charge the unit with 

refrigerant.  If present, the ETV will be forced fully open.  The technician is prompted to install a battery charger to 

guarantee sufficient voltage to keep all valves open during the evacuation and charging process. 

 

 

 

4-73  

31 January 2005 

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR-2 SmartReefer2

ABB ControlMaster CM15 Commissioning Instructions preview
ControlMaster CM15
Бренд: ABB Страницы: 28
GE RSTi-EP User Manual preview
RSTi-EP
Бренд: GE Страницы: 425
Kasco C10 Installation & Operation Manual preview
C10
Бренд: Kasco Страницы: 3
Federal Signal Corporation ultravoice UV Installation, Operation And Service Manual preview
ultravoice UV
Бренд: Federal Signal Corporation Страницы: 79
Federal Signal Corporation PAGASYS GEN II Description, Installation, And User Manual preview
PAGASYS GEN II
Бренд: Federal Signal Corporation Страницы: 32
Jedia JMA-5104 Operating Instructions Manual preview
JMA-5104
Бренд: Jedia Страницы: 12
JED Micro T470 User And Installation Manual preview
T470
Бренд: JED Micro Страницы: 10
JCM Technologies SESAME Rapid Installation Manual preview
SESAME
Бренд: JCM Technologies Страницы: 2
Veeder-Root TLS Install, Setup, & Operation Manual preview
TLS
Бренд: Veeder-Root Страницы: 27
Valve Concepts 1078 Installation, Operation And Maintenance Manual preview
1078
Бренд: Valve Concepts Страницы: 18
K&K M1500 Installation Instructions Manual preview
M1500
Бренд: K&K Страницы: 6
KAESER KOMPRESSOREN SIGMA CONTROL 2 User Manual preview
SIGMA CONTROL 2
Бренд: KAESER KOMPRESSOREN Страницы: 246
NAD C 399 Addendum Sheet preview
C 399
Бренд: NAD Страницы: 4
NAD C388 Addendum Sheet preview
C388
Бренд: NAD Страницы: 4
UniPOS VIT 01 Instruction Manual preview
VIT 01
Бренд: UniPOS Страницы: 51
Unipulse F159 Operation Manual preview
F159
Бренд: Unipulse Страницы: 126
YachtSafe W010 Manual preview
W010
Бренд: YachtSafe Страницы: 3
Ziton ZP1-X3E Series Operation Manual preview
ZP1-X3E Series
Бренд: Ziton Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды