Thermo King SR-2 SmartReefer2 Скачать руководство пользователя страница 38

Страница: 38 / 431

Section 2 – SR-2 Hardware Description

Control and Display Return Air Sensors

These sensors

monitor the temperature of the air

returning to the evaporator coil. The sensors are

located in the return air flow and are connected

directly to the microprocessor connector J3. These

sensors are graded sensors and must be replaced

with graded sensors. The microprocessor must be

calibrated to the respective grade of the installed

sensor in order to operate properly. The Control

Return Air Sensor is marked with one yellow cable

tie and is connected to the microprocessor via the

RTP and RTN wires. The Display Return Air Sensor

is marked with two yellow cable ties and is

connected to the microprocessor via the RTRP and

RTRN wires.

Control and Display Discharge Air

Sensors

These sensors monitor the temperature of the air

leaving the evaporator coil. The sensors are located

in the evaporator discharge air path and are

connected directly to the microprocessor via

connector J3. These sensors are graded sensors

and must be replaced with graded sensors. The

microprocessor must be calibrated to the respective

grade of the installed sensor, in order to operate

properly. The Control Discharge Air Sensor is

marked with one red cable tie and is connected to

the microprocessor via the DTP and DTN wires.

The Display Discharge Air Sensor is marked with

two red cable ties and is connected to the

microprocessor via the DTRP and DTRN wires.

Coil Temperature Sensor

This sensor monitors the temperature of the

evaporator coil. The sensor is located on the

evaporator coil header plate and is connected

directly to the microprocessor via connector J3. This

is an un-graded sensor. It is connected to the

microprocessor via the CTP and CTN wires.

Ambient Temperature Sensor

This sensor monitors the ambient air temperature.

The sensor is located in the main unit adjacent to

the condenser coil and is connected directly to the

microprocessor via connector J3. This is an un-

graded sensor. It is connected to the micro-

processor via the ATP and ATN wires.

Spare 1 Temperature Sensor

This optional sensor monitors a temperature as

selected by the customer. This optional sensor must

be installed as required by the customer. This is a

graded sensor. It is connected to the micro-

processor via the STIP and STIN wires.

New Style Graded Sensor

New Style Un-graded Sensor

with Yellow Shrink Tube Marker

2-22

31 January 2005

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Результаты поиска

Содержание SR-2 SmartReefer2

Отзывы:

Похожие инструкции для SR-2 SmartReefer2

Бренды по названию

Популярные бренды

Thermo King SR-2 SmartReefer2, Руководство по диагностике

Результаты поиска

Содержание SR-2 SmartReefer2

Отзывы:

Похожие инструкции для SR-2 SmartReefer2

Бренды по названию

Популярные бренды