TEXIO DL-2060 Скачать руководство пользователя страница 5

Страница: 5 / 152

USING THE PRODUCT SAFELY

WARNING and CAUTION

■

Do not remove the product's covers and panels

Never remove the product's covers and panels for any purpose.

Otherwise, the user's electric shock or a fire may be incurred.

■

Warning on using the product

The warning items given below are to avoid danger to the user's body and life and avoid the damage and deterioration

of the product. Use the product, observing the following warning and caution items.

■

Warning items on power supply

●

Power supply voltage

This equipment operates from a power source that does not apply more than 250V rms between the supply

conductors or between either supply conductor and ground. A protective ground connection by way of the

grounding conductor in the power cord is essential for safe operation.

●

Power cord

Important: The attached power cord set can be used for this device only.

If the attached power cord is damaged, stop using it and call the company or each sales office.

If the power cord is used without the damage being removed, an electric shock or fire may be caused.

●

Protection fuse

If an input protection fuse is blown, the product does not operate. When the fuse is blown, the user can replace it.

However, replace it correctly, observing the warning and caution items that are provided in the section of the

manual where the fuse replacement is explained. If the fuse is incorrectly replaced, a fire may occur.

●

Changing the power supply voltage

The product enables to change operational power supply voltage by switch over the inlet at rear panel. Please

refer to the section

“1.1.2.2 To change fuse”.

■

Warning item on grounding

The product has the GND terminal on the panel surface to protect the user from electric shock and protect the product.

Be sure to ground the product to safely use it.

■

Warning item on installation environment

●

Operating temperature

Use the product within the operating temperature indicated in the rating column. If the product is used with the

vents of the product blocked or in high ambient temperatures, a fire may occur.

●

Operating humidity

Use the product within the operating humidity indicated in the rating column. Watch out for condensation by a

sharp humidity change such as transfer to a room with a different humidity. Also, do not operate the product with

wet hands. Otherwise, an electric shock or fire may occur.

●

Use in a gas

Use in and around a place where an inflammable or explosive gas or steam is generated or stored may result in an

explosion and fire. Do not operate the product in such an environment.

Also, use in and around a place where a corrosive gas is generated or spreading causes a serious damage to the

product. Do not use the product in such an environment.

●

Do not let foreign matter in

Do not insert metal and flammable materials into the product from its vent and spill water on it. Otherwise, an

electric shock and fire may occur.

Содержание DL-2060

























































































































































Результаты поиска

Содержание DL-2060

Отзывы:

Похожие инструкции для DL-2060

Бренды по названию

Популярные бренды

TEXIO DL-2060, Инструкция по эксплуатации

Результаты поиска

Содержание DL-2060

Отзывы:

Похожие инструкции для DL-2060

Бренды по названию

Популярные бренды