TEXIO DL-2060 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 152

background image

36

The moving average filter puts the specified number of reading conversions in a first-in,
first-out order. The very first measurement reading simply fills up the stack. To yield a
reading for display, the filter produces an average of the stacked measurement readings
every time a new measurement reading is available and replaces the oldest reading in the
stack. In the repeating average mode, the multimeter waits for the measurement reading
stack to fill up and then take an average to produce a reading for display. It then flushes
the stack and starts over with an empty stack. Consequently, the repeating digital filter
yields one reading for display every specified number of measurement readings.

Digital filter is not available for diode, continuity, frequency and period measurements.

Default

The digital filter is enabled and is in moving average mode with 10 readings by default.

How to enable/disable digital filter

Press FILTER button to switch the digital filter function. The “FILT” anunnciator
indicates the state of the digital filter. When it is lit, the filter is enabled.

How to configure digital filter:

You can configure the digital Filter either through the front panel operation or through
the remote interface operation.

Front Panel Operation

For READINGS setting, please press CONFIG and then FILTER button for selecting
READINGS. Press ENTER to access. Use

◁

,

▷

,

△

and

▽

buttons to set the READINGS

(from 2 to 100) in order to get an average value. Press ENTER when it’s ready.
For MODE setting, please press CONFIG and then FILTER button for selecting MODE. Press
ENTER to access. Use

◁

,

▷

to select MOVING AVG. or REPEAT AVG.. Please ENTER to

confirm.
Press ESC button to enable or disable this function.

Remote Interface Operation

Use the following commands to set your digital filter:

SENSe:AVERage:TCONtrol {MOVing|REPeat}
SENSe:AVERage:TCONtrol?
SENSe:AVERage:COUNt {<

value

>|MINimum|MAXimum}

SENSe:AVERage:COUNt? [MINimum|MAXimum]
SENSe:AVERage:STATe {OFF|ON}
SENSe:AVERage:STATe?

«
...
40
41
42
43
44
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL-2060

Бренд: Omega Страницы: 21

Бренд: Omega Страницы: 17

Бренд: Kane Страницы: 24

Бренд: Agilent Technologies Страницы: 15

Бренд: Fluke Страницы: 20

Бренд: Tenma Страницы: 25

Бренд: APPA Страницы: 18

Бренд: Keysight Страницы: 83

Бренд: PeakTech Страницы: 55

Бренд: PeakTech Страницы: 64

Бренд: Kaiweets Страницы: 32

Бренд: UNI-T Страницы: 42

Бренд: Wabtec Страницы: 60

Бренд: Tenmars Страницы: 40

Бренд: Campbell Страницы: 46

Бренд: TC Communications Страницы: 26

Бренд: APPA Страницы: 78

Бренд: Omega Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды