TEXIO DL-2060 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 152

background image

46

Front Panel Operation

1.

Configure the thermocouple type and unit. Pressing CONFIG > SHIFT > TEMP (TCOUPL),
and then using PREV and NEXT to select the type and unit.

2.

Measure a known and accurate reference temperature (T1). The result showing on the
DL-2060 is (T2).

3.

Adjust the simulated value (23.0°C to 23.0°C + T3.)

4.

Configure the Simulated value by pressing CONFIG > SHIFT > TEMP(TCOUPL) > NEXT >
SIMULATED > ENTER, and by buttons

「

PREV

」

or

「

NEXT

」

and

△

&

▽

assistance to

adjust the value.

Remote Interface Operation

Use the following commands to set up the thermocouple configuration.

SENSe:UNIT {Cel|Far|K}
SENSe:UNIT?
SENSe:TCOuple:TYPE {E|J|K|N|R|S|T}

※

SENSe:TCOuple:RJUNCtion:SIMulated {<

value

>|MINimum|MAXimum}

※

SENSe:TCOuple:RJUNCtion:SIMulated?

※

This command is available with firmware version 1.05 or upward.

3.1.9 Remote Interface Selection

The multimeter supports GP-IB (G/VG type), RS-232C(R/VR type) and USB interfaces,
but only one interface can be activated at a time. If you are using GP-IB, you must set
the address for the multimeter. You can set the address to any value from 0 and 31. The
address is set to “22” when the multimeter is shipped from the factory.
If you are using RS-232C, you must set the baudrate and parity for the multimeter.

※

Note: The remote interface can only be set through the front panel operations.

How to select a remote interface

Press MENU and then use

◁

and

▷

to select INTERFACE. Then Press ENTER on your

choice of USB or GPIB interface.

How to set address when using GP-IB

Press MENU and then use

◁

and

▷

to access INTERFACE. Select GPIB to set address.

Use

◁,

▷,

△

and

▽

to adjust the numbers to the desired address. Press ENTER to set

it.

How to set baudrate when using RS-232C

Press MENU and then use

◁

and

▷

to access INTERFACE. Select RS232, Select

«
...
50
51
52
53
54
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL-2060

Бренд: Vaisala Страницы: 71

Бренд: Steinberg Systems Страницы: 21

Бренд: ProportionAir Страницы: 4

D/I Mux III System

Бренд: Coastcom Страницы: 329

Бренд: Zutemer Страницы: 8

Escola 2 1006811

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 5

Бренд: Mastech Страницы: 8

Бренд: UNI-T Страницы: 1

Бренд: UNI-T Страницы: 42

Бренд: LIMIT Страницы: 149

Бренд: YOKOGAWA Страницы: 2

Бренд: Keithley Страницы: 13

Бренд: Pyle Страницы: 2

Бренд: Datacom Страницы: 106

Бренд: Velleman Страницы: 80

Бренд: Velleman Страницы: 93

Бренд: Velleman Страницы: 106

Бренд: Velleman Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды