TEXIO DL-2060 Скачать руководство пользователя страница 31

Страница: 31 / 152

Figure 3-9

2.4 Frequency & Period Measurements

DL-2060 uses an on-board counter with 25MHz to measure the frequency (period). The
measurement band is from 3Hz to 300kHz (or 333 ms to 3.3

s) and the measurement

voltages range from 100mV to 750 V in AC. The default for “RANGE” is auto-range.

Warning! The maximum input allowed is 1000V

(peak). Applying excess voltage

may damage your meter.

How to measure frequency and period

①

Selects input signal connections on front or rear panel.

②

Connect the test leads to the terminals as shown in

Figure 3-2

③

Set RESOLUTION (Refer to 3.1.1) and INPUT JACK. Or skip this step if default is to be
used.

④

Press FREQ button for frequency measurement or SHIFT + PERIOD(FREQ) buttons
for period measurement.

⑤

Select the auto-range function by pressing AUTO button on the front panel or use

△

and

▽

buttons to select the desired range.

⑥

Connect test leads to your source signal and observe the reading shown on the
display. If the input signal is beyond the allowed range, an overflow message “OVLD”
will be displayed.

※

Note: The rear terminal panel can

also be used via the same procedures as the front

panel. (Please refer to

Figure 3-3

)

Содержание DL-2060

























































































































































Результаты поиска

Содержание DL-2060

Отзывы:

TEXIO DL-2060, Инструкция по эксплуатации, Страница: 31 / 152

Результаты поиска

Содержание DL-2060

Отзывы: