TEXIO DL-2060 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 152

background image

110

MEASure:CURRent:AC? {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and make a AC current measurement with the specified range and resolution. The reading
is sent to the output buffer. For AC measurement, resolution is fixed at 6 ½ digits. Therefore the
resolution parameter only affects the front panel display.

MEASure:RESistance? {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and make a 2-wire Ω measurement with the specified range and resolution. The reading is
sent to the output buffer.

MEASure:FRESistance? {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and make a 4-wire Ω measurement with the specified range and resolution. The reading is
sent to the output buffer.

MEASure:FREQuency? {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and make a frequency measurement with the specified range and resolution. The reading
is sent to the output buffer. For frequency measurements, the meter uses only one “range” for all
inputs between 3Hz and 300kHz. With no input signal applied, frequency measurements return
“0”.

MEASure:PERiod? {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and make a period measurement with the specified range and resolution. The reading is
sent to the output buffer. For period measurements, the meter uses only one “range” for all
inputs between 0.33 seconds and 3.3

μ

sec. With no input signal applied, period measurements

return “0”.

MEASure:CONTinuity?

Preset and make a continuity measurement. The reading is sent to the output buffer. The range
and resolution are fixed at 1kΩ and 5 ½ digits respectively.

MEASure:DIODe?

Preset and make a diode measurement. The reading is sent to the output buffer. The range and

resolution are fixed at 1Vdc with 1mA current source and 5 ½ digits respectively.

MEASure:TEMPerature?

Preset and make a temperature measurement with RTD. The reading is sent to the output buffer.

MEASure:TCOuple?

Preset and make a temperature measurement with thermocouple. The reading is sent to the

output buffer.

«
...
114
115
116
117
118
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL-2060

Бренд: UEi Страницы: 12

Бренд: Contrel Страницы: 16

Бренд: DCB Страницы: 33

Бренд: Fiber Options Страницы: 8

Бренд: ZOTEK Страницы: 2

Бренд: PCWork Страницы: 152

Бренд: PCE Health and Fitness Страницы: 13

Бренд: CEN-TECH Страницы: 27

Бренд: INTER ELEKTRIK ELEKTRONIK Страницы: 3

Бренд: Miranda Страницы: 19

Бренд: UNI-T Страницы: 33

Бренд: UNI-T Страницы: 30

Бренд: UNI-T Страницы: 34

Бренд: UNI-T Страницы: 31

Бренд: UNI-T Страницы: 42

Бренд: UNI-T Страницы: 38

Бренд: UNI-T Страницы: 49

Бренд: Pro's Kit Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды