TEXIO DL-2060 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 152

TEXIO DL-2060 Скачать руководство пользователя страница 41

35

Table 4-2

Bandwidth

AC Filter

Time

( seconds per reading)

3 Hz – 300 kHz

Slow

7

20 Hz

–

300 kHz

Medium

1

200 Hz

–

300 kHz

Fast

0.1

How to set AC Filter in AC measurements:

User can set the AC Filter either through the front panel operation or through the remote
interface operation.

Front Panel Operation

Press CONFIG + ACV button. Use

◁

and

▷

buttons to locate “BAND WIDTH”

submenu, and then press ENTER to select it. Look for the desired bandwidth using

◁

and

▷

buttons. Then press ENTER on your selection. There are three options: 3Hz,

20Hz and 200Hz. The locations of these buttons are shown with red rectangle frames in

Figure 4-2

.

Figure 4-2

Remote Interface Operation

From your PC terminal, use the following command to specify the filter type:

DETector:BANDwidth {3|20|200|MIN|MAX}

3.1.2.2 Digital Filter

Definition:

DL-2060 uses an averaging digital filter to yield a reading for display from a specified
number of measurement readings in the past. The past measurement readings are
stored in a stack of memory. The number may be in the range of 2 to 100. User may
select one of the two modes of digital filter operations: Moving Average and Repeating
Average.

«
...
39
40
41
42
43
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов