TEXIO DL-2060 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 152

TEXIO DL-2060 Скачать руководство пользователя страница 63

57

3.3.2 % (Percent)

Definition

This mathematical function calculates the ratio of a measurement reading to a specified
target value as the form of percentage. The calculation formula is shown below:

The specified target value is store in a volatile memory and will be cleared after the
meter has been turned off or a remote interface reset.

How to use % (Percent) function

There are two ways to make a percent measurement: Through the front panel operation
or through the remote interface operation.

Front Panel Operation

To specify a target value, user needs to configure Percent function by pressing %,
then use

◁

and

▷

to move through the digits and

△

and

▽

buttons to increase or

decrease the numbers to a desired target value. Press ENTER to set the value. Press % to
activate this function. And then observe the calculated percent value on the display as
shown as

Figure 4-15

.

※

Note: Press % again to disable this function. The “MATH” annunciator on the display

indicates the state of a mathematical feature.

Figure 4-15

Remote Interface Operation

Use the following commands to enable and configure Percent function:

CALCulate:FUNCtion PERCent
CALCulate:STATe {OFF|ON}
CALCulate:STATe?
CALCulate:PERCent:TARGet {<

value

>|MINimum|MAXimum}

CALCulate:PERCent:TARGet? [MINimum|MAXimum]

«
...
61
62
63
64
65
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов