background image

 

 

69 

Default 

The beeper is enabled when it is shipped from the factory. The beeper state is stored in 
a volatile memory and the default will be restored when the meter has been turned off or 
after a remote interface reset. 
 

How to control the beeper 

User can control the beeper from either the front panel operation or the remote interface 
operation.   
 

Front Panel Operation 

Follow the procedure below to disable or enable the beeper:

 

Press MENU button then use 

  and 

  buttons to find SYSTEM menu. Press

 

ENTER to choose it, and then again use 

  and 

  buttons to find BEEP menu. Press

 

ENTER to choose it, and then find ON or OFF 

by using 

  and 

  buttons. Press ENTER on your selection.

 

The locations of the buttons 

are shown with red rectangle frames in 

Figure 4-27

 
Procedures: MENU 

 SYSTEM 

 BEEP

 {ON|OFF} 

 

 

Figure 4-27 

 

Remote Interface Operation 

The following commands show how to use the remote interface operation to disable or 
enable the beeper: 
 

SYSTem:BEEPer 
SYSTem:BEEPer:STATe {OFF|ON} 

 

3.4.3    Reading Memory (Store & Recall) 

DL-2060  has  a  memory  capacity  of  2000  readings.  The  readings  are  stored  in 
first-in-first-out order and the memory type is volatile, which means the stored readings 
will be cleared when the multimeter is power-off. The reading memory feature can be 

 

 

 

Содержание DL-2060

























































































































































Отзывы: