TEXIO DL-2060 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 152

background image

37

3.1.3 Resolution Setting (Digits)

Definition

Resolution  is  the  number  of  digits  a  multimeter  can  measure.  User  can  select  the
resolution for a specific measurement. The choices for the resolution setting are: fast 4
1/2, slow 4 1/2, fast 5 1/2, slow 5 1/2, fast 6 1/2 and slow 6 1/2. For a higher accuracy,
user can select 6 1/2 digit resolution. For a faster measurement, user can select 4 1/2 digit
resolution.

The resolution setting applies to all math operations under the selected measurement
function. The selected value is stored in a volatile memory and the setting is only valid
for the current measurement function. User can select different resolution for different
measurement function.

Default

The default value for the resolution is slow 5 1/2 digit and the default value will be restored
when the meter has been turned off or after a remote interface reset. The user selected
value for the resolution setting is stored in a volatile memory and the setting is only valid
for the current measurement function. Please refer to

Table 2-1

on

※

Note: The resolution setting for AC measurements is actually fixed at 6 ½ digits.

When user selects a lower resolution, the meter will mask out the extra digits. User’s
selection of resolution for AC function will not affect the actual speed or accuracy.

How to set the resolution

The resolution can be set either through the front panel or the remote interface
operation.

Front Panel Operation

There are two ways to set the resolution. The locations of the buttons are shown with red
rectangle frames in

Figure 4-3

.

A.



First select your desired measurement function by pressing one of the function
buttons located on the first row of your meter's front panel.



Press DIGITS button to select your desired resolution for your measurement. User
can press DIGITS button several times to see how the resolution setting changes
from 4 1/2, 5 1/2 to 6 1/2.

※

Note: When using Method A to set the resolution, your options are 4 1/2 (slow), 5 1/2

(slow) and 6 1/2 (fast).

«
...
41
42
43
44
45
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL-2060

Бренд: Keithley Страницы: 106

Бренд: Keithley Страницы: 60

Бренд: Huayi Страницы: 46

Бренд: Greenlee Страницы: 64

Бренд: Di-LOG Страницы: 32

Бренд: Sifam Tinsley Страницы: 16

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 6

Бренд: koban Страницы: 24

Бренд: SIGLENT Страницы: 108

Бренд: SIGLENT Страницы: 236

Бренд: Schmidt Страницы: 16

HOTWIRE 8610 DSLAM

Бренд: Paradyne Страницы: 56

Бренд: Dawson Tools Страницы: 8

Бренд: TDE Instruments Страницы: 16

Бренд: Velleman Страницы: 70

MULTI18HP230V1A

Бренд: Gree Страницы: 131

Бренд: Quick Eagle Networks Страницы: 162

Бренд: Extech Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды