TEXIO DL-2060 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 152

background image

38

B.



Press CONFIG and then select a function as you wish from DCV, DCI (SHIFT +DCV),
Ω2, Ω4 (SHIFT + Ω2), FREQ and PERIOD (SHIFT + FREQ).



Press ENTER on RESOLUTION submenu. If it is not shown on the display, use

◁

and

▷

to locate it.



Use

◁

and

▷

to find your desired resolution. Press ENTER on your choice.

※

Note: The resolution of AC measurements is fixed at 6 1/2 digit.

※

Note: The options for frequency and period measurements are 4 1/2 (slow), 5 1/2

(slow) and 6 1/2 (slow).

Figure 4-3

Remote Interface Operation

Use the following commands on your PC terminal to set the resolution for your
measurement.

CONFigure:<function> <range>,<resolution>
MEASure:<function>? <range>,<resolution>
SENSe:<function>:RESolution <resolution>

Users can specify the resolution in the same units as the measurement function, not in
number of digits. For instance, specify the resolution in volts and the frequency in herts.
The examples are in the following.

CONF:VOLT:DC 10,0.001                         (4 1/2 digits on the10Vdc range)
MEAS:CURR:AC? 1,1E-6                            (6 1/2 digits on the1A range)
CONF:FREQ 1kHz,0.1Hz                            (1000 Hz input, 0.1Hz resolution)
VOLT:AC:RES 0.05                                        (50mV resolution on the ac function)

or

«
...
42
43
44
45
46
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL-2060

Бренд: Microsemi Страницы: 36

Бренд: SW Stahl PROFI Tools Страницы: 72

Бренд: Kaise Страницы: 2

Бренд: UNI-T Страницы: 60

Бренд: UNI-T Страницы: 62

Бренд: APPA Страницы: 137

Бренд: IEK Страницы: 28

Бренд: Würth Страницы: 58

Бренд: Würth Страницы: 240

Бренд: Brymen Страницы: 16

Бренд: Perfomance Tool Страницы: 16

Бренд: PeakTech Страницы: 40

Бренд: PeakTech Страницы: 60

Бренд: PeakTech Страницы: 64

Бренд: Amprobe Страницы: 6

Бренд: Amprobe Страницы: 74

Бренд: Artistic Licence Страницы: 9

Бренд: Major tech Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды