Teledyne PATHFINDER Скачать руководство пользователя страница 137

Страница: 137 / 240

Pathfinder DVL Guide

April

2018

EAR-Controlled Technology Subject to Restrictions Contained on the Cover Page.

Page 125

EZ - Sensor Source

Purpose

Selects the source of environmental sensor data.

Format

EZcdhprstu

The EZ command work ONLY without the # sign.

Range

Firmware switches (see description)

Default

EZ 10000010

The default setting for this command is recommended for most applications.

Description

Setting the EZ-command firmware switches tells the Pathfinder to use data from a man-

ual setting or from an associated sensor. When a switch value is nonzero, the Pathfinder

overrides the manual E-command setting and uses data from the appropriate sensor. If

the sensor specified by this command is not available, the best alternate sensor will be

used (see the

EY – Sensor Source Override for Doppler Parameters

command for more

information).

The following table shows how to interpret the sensor source switch settings.

Table 28:

Sensor Source Switch Settings

FIELD

VALUE = 0

VALUE = 1

VALUE = 2

Speed of

sound

Manual #EC (see

EC - Speed of Sound

)

Calculates using available depth, salinity

and temperature.

External Speed of Sound Sensor

Depth

Manual ED (see

ED - Depth of Transducer

)

Internal Keller pressure sensor

External Depth Sensor

Heading

Manual #EH (see

EH - Heading

)

Internal SBG AHRS

External Compass

Pitch (tilt 1)

Manual #EP (see

EP - Pitch and Roll Angles

)

Internal SBG AHRS

External Compass

Roll (tilt 2)

Manual #ER (see

ER - Roll Angle

)

Not used (Roll source specified by Pitch

field)

Not used (Roll source specified by Pitch

field)

Salinity

Manual ES (see

ES – Salinity

)

Not Allowed

External Salinity Sensor

Temp

Manual #ET (see

ET - Temperature

)

Internal transducer sensor

External Temp Sensor

Up/Down

Orientation

Manual #EU (see

EU - Up/Down Orientation

)

Not Allowed

Example

EZ10000010 means calculate speed of sound from available depth salinity and tempera-

ture, use ED depth, EH heading, ES command sets salinity, TRDI internal temperature

sensor, manual up/down orientation set with the EU command.

When a PS1-command is sent, the displayed Fixed Leader data shows the available internal sensors
connected to the

Pathfinder

DVL. It does not show external sensors. To interpret this PS1 field, convert

the value to binary.

If EZ pitch is one (internal sensor), a pendulum pitch correction will be applied that removes the effect

of roll on pitch. This effect is common to most tilt sensors (electrolytic tilt and pendulum).
The pitch field of the EZ command controls the source for roll. The roll field is ignored and has only been

retained for legacy purposes.
The heading coordinate frame is determined by the coordinate frame parameter of the #EH command

for any heading source (command, internal or external). The pitch and roll coordinate frame is specified

by the coordinate frame parameter of the #EP command for any heading source (command, internal or
external). See

EH - Heading

and

EP - Pitch and Roll Angles

for more details.

Содержание PATHFINDER

















































































































































































































































Результаты поиска

Содержание PATHFINDER

Отзывы:

Teledyne PATHFINDER, Руководство пользователя, Страница: 137 / 240

Результаты поиска

Содержание PATHFINDER

Отзывы: