Teledyne PATHFINDER Скачать руководство пользователя страница 132

Страница: 132 / 240

April

2018

Pathfinder DVL Guide

Page 120

EAR-Controlled Technology Subject to Restrictions Contained on the Cover Page.

EH - Heading

Purpose

Sets the Pathfinder heading and the coordinate frame (instrument or ship) to which EH-

command input refers.

Format

EHxxxx, y

The EH command works with or without the # sign. For example, using EH or #EH are both

valid commands.

Range

xxxx = 0 to 35999 1/100ths of a degree

y = 0 for instrument coordinates

y = 1 for ship coordinates

Default

EH0,0 (Stationary systems), EH0,1 (Vessel)

The default setting for this command is recommended for most applications.

Description

EH sets the Pathfinder heading and heading coordinate frame if both arguments are en-

tered.
EH sets the Pathfinder heading if only one argument is entered. This heading value is as-

sumed to be in instrument coordinates. Figure 18

shows transducer beam axis and tilt

signs.
EH may be entered after the unit is commanded to ping (CS command) and will be used

in subsequent pings.

Example

Convert heading values of +21.5 degrees to EH-command values referenced to ship coor-

dinates.

Heading in hundredths = 21.50º × 100 = 2150
EH 2150, 1 (+ in front of 2150 is optional)

If the EZ Heading field = 1, the Pathfinder overrides the manually-set EH value and uses

heading from the transducer’s internal sensor. If the EZ Heading field = two the Pathfinder

takes heading from an external synchro. If EZ Heading field is zero the Pathfinder uses the

manual EH command settings.
See

EZ - Sensor Source

for more details and restrictions for the case of mixed heading

sources.

EP - Pitch and Roll Angles

Purpose

Sets the Pathfinder pitch (tilt 1) and, optionally, the roll (tilt 2) and the coordinate frame

(instrument or ship) to which all pitch and roll inputs (including sensors) refer. Alterna-

tively, the EP commands may be used with single arguments, in which case it is assumed

that the pitch and roll inputs represent the pitch and roll of the instrument rather than

those of the ship.

Format

EP±xxxxx, ±yyyyy, z

The EP command works with or without the # sign. For example, using EP or #EP are both

valid commands.

Содержание PATHFINDER

















































































































































































































































Результаты поиска

Содержание PATHFINDER

Отзывы:

Teledyne PATHFINDER, Руководство пользователя, Страница: 132 / 240

Результаты поиска

Содержание PATHFINDER

Отзывы: