Teledyne HDO9000 Скачать руководство пользователя страница 87

Страница: 87 / 188

Display

Trace Intensity

Choose a line style for traces: solid

Line

or disconnected sample

Points

When more data is available than can actually be displayed, Trace Intensity helps to visualize

significant events by applying an algorithm that dims less frequently occurring samples. Touch

Intensity

and enter a value from 0 to 100.

Intensity 40% (left) dims samples that occur ≤ 40% of the time to highlight the more frequent samples,

vs. intensity 100% (right) which shows all samples the same.

XY Plots

XY plots display the phase shift between otherwise identical signals. They can be used to display

either voltage or frequency on both axes, each axis now corresponding to a different signal input,

rather than a different parameter. The shape of the resulting pattern reveals information about phase

difference and frequency ratio.

Note:

The inputs can be any combination of channels, math functions, or memories, but both

sources must have the same X-axis scale.

Choose an XY grid mode and select the sources for

Input X

and

Input Y

Sequence Display Mode

Use these settings to select the

Display Mode

used when sampling in

Sequence mode

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды