Teledyne HDO9000 Скачать руководство пользователя страница 141

Страница: 141 / 188

Analysis Tools

Make Mask

Use this procedure to create a new mask based on a live waveform. The mask covers the area of the

waveform plus the boundaries you enter.

1. Open the

Make Mask

subdialog.

2. If desired, enter a new

Destination File Name

and path, or touch Browse and select a previous

file to overwrite. The file name should end with the

.msk

extension.

3. Touch the

Ver Delta

and

Hor Delta

fields and enter boundary values using the pop-up Virtual

Keypad or the front panel Adjust knob.

4. Touch

Make from Trace

Load Mask

Use this procedure in lieu of Make Mask if you have a pre-defined mask file, or wish to recall a mask

you previously created and saved.

1. Open the

Load Mask

subdialog.

2. To use a saved .msk file, touch

File

and select the mask.

To use an industry standard mask, touch

Standard

and select the mask from the pop-up.

3. Check

View Mask

to display the mask over the trace.

Remove a Mask from the Display

Touch the

Delete All Masks

button. Alternatively, open the

dialog where a particular mask is set,

and on the

Load Mask

subdialog, touch

Delete

Set Gates

Set gates to limit the portion of the waveform that is compared to the mask.

1. Open the

Gate

subdialog.

2. Enter the

Start

and

Stop

horizontal divisions that mark the segment of the waveform to be

tested with this mask. This can be a whole division or a fraction of a division. Divisions are

numbered 1-

left to right.

A quick way to position the gate is to drag the gate posts initially placed at the extreme left

and right ends of the grid to the desired points.

Define "True"

1. Open the

Test

subdialog.

2. Select one of the conditions that, when True (yes), results in a Pass.

3. Optionally, turn

Off/On

markers. Markers visually indicate where on the waveform mask

violations have occurred.

131

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды