Teledyne HDO9000 Скачать руководство пользователя страница 42

Страница: 42 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Zx Dialog

Behind the main Zoom dialog is a separate tab for each potential zoom trace (Z1-Z

). Each Z

dialog

reflects the current scale settings for that zoom trace. Use it to adjust the zoom magnification.

Trace Controls

Trace On

shows/hides the zoom trace. It is selected by default when the zoom is created.

Source

lets you change the source for this zoom to any channel, math, or memory trace while

maintaining all other settings.

Segment Controls

These controls are used in

Sequence Sampling Mode.

Zoom Factor Controls

Out

and

In buttons

increase/decrease zoom magnification and consequently change the

Horizontal and Vertical Scale settings. Touch either button until you've achieved the desired

level.

Var.checkbox

enables zooming in single increments.

Horizontal Scale/div

sets the time represented by each horizontal division of the grid. It is the

equivalent of Time/div in channel traces, only unlike that setting, it may differ for each zoom

trace.

Vertical Scale/div

sets the voltage level represented by each vertical division of the grid; it's

the equivalent of V/div in channel traces.

Horizontal/Vertical Center

sets the time/voltage at the center of the grid. The horizontal center

is the same for all zoom traces.

Reset Zoom

returns the zoom to x1 magnification.

Creating Zooms

Zooms magnify a selected region of another trace by altering the Horizontal Scale relative to the

source trace. Any type of trace can be "zoomed" by creating a new zoom trace (Z

) following the

procedures here.

Note:

Alternatively, channel or math traces can be "zoomed" by pinching/unpinching two

fingers over the trace. This method does not create a separate zoom trace. With channel

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды